EER3000L02BB General Electric Range - Instructions

remove rear panel cover, removered four screws that held control panel, disconnected colored wires, removed circuit control board, reinstall new board and connected color coded wire to the correct spot on the board, plugged in 220 volt cord, switch on circuit breaker, everything worked normal again

remove two bolts in on sensor and slip thru back un plug and reverse to put in

Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven removed. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.

Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.

replacement was easy. pulled away the stove from wall. unplug the stove. open oven door. remove the two hex head screws holdings stove top. raise the stove top in the front. supported stove top with a 16 inch piece of wood. place New Burner under old burner. remove old burner remove wires remove old burner and place it on top of new burner connected the wires from burner to new burner. install new burner. remove support lowered top down. plugged in stove tested. .burner. burner w.ork fine. reinstall hex head screws back top. pushback stove back into the wall. testes over again. all the stove work done.

Went super fast--very easy. Part fit perfectly and the installation was a snap.

Pull stove out from the wall unplug it remove the old switches and replaced them withe new one. they work just fine.

Removed two screws and lifted up the top of the stove to replace the broken handle with the new one.

My Range had the issue I mentioned here. I put off the repairs for a long time, but Thanksgiving was around the corner and we needed a working oven. I had made a previous call to repair man and was quoted $75.00 for a service call to come and check the issue. Before calling a repair man back, I decided to pull the rear cover off the range to see how complicated it would be to repair. I removed the rear cover and found that everything was connected to this "Oven Electronic Control" except for the top elements (explaining why they still worked and the oven didn't). This made it seem that this part would surely have to be causing the issue. I did a search on Google and found this company and the part that I needed. The cost of the part was less than the service call for a repair man would have been. I ordered the part and paid for next day delivery. The part shipped on Monday and arrived on Tuesday. For the installation, I had to identify the wiring because the connector layout was a little different. When I looked closely I found that the terminals were numbered the same as the old part. I replaced wire for wire, put it all back together and tried it out. It worked like a champ. I was thrilled to have been able to find the part with schematics on this web site and it was the correct part and fixed the problem. I was also thrilled that I saved a couple hundred dollars fixing it myself and that it was so easy. I would highly recommend this company for the ease of use of finding the part on their web site, the reasonable price and their prompt processing and delivery.

Identified part and part # using schematic found on GE website, contacted PartSelect and confirmed part number, ordered and paid for part. Two days later I recieved part. Unplugged stove, removed two screws on bottom side of front panel and two on top back of same panel, pulled panel forward, pulled the control knob off, removed two small screws that hold the control switch in place, situated new control switch next to bad switch and removed one wire at the time from the bad switch and connected to the same terminal on the new switch. Put everything back together and Bingo, works like a new one. Thanks PartSelect for the friendly, personal phone service, the fast shipment and competitive pricing on my part.

Changed out the burner with a new replacement and it still didn't work. The socket on the old burner had a burn mark on it. The infinite switch operated sloppy not crisp like the other burners.Ordered a replacement online. Moved the range away from wall and cabinet and shut off electric at panel box. Removed upper back panel. removed switch knob and 2 screws holding switch. Compared electrical connections of both switches and saw that they were different. Read instructions which were included with new switch and found diagram for connecting old lead to new lead correctly. After all leads were connected, remounted new switch powered up and tested OK.

Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.

This was the second replacement glass I've bought, but I'm unsure if the first one was from PartsSelect or GE directly. It was a couple years ago when I purchased the first one. The first one popped in rather easily. I scraped out the rust and debris that had built up within the lower metal track and then inserted the glass. By pulling upwards on the door handle I had just enough room to pop it into the upper plastic tabs. The second door I bought was harder. I truly feel the second was larger. I tried the original procedure, but there was significantly more glass at the top, and I couldn't push up on the handle to even clear the handle itself. I removed the glass to re-cleaned the lower track, but it was clear of debris, so that wasn't the problem. I had to completely dismantle the outside plastic frame, insert the window and put it back together. It did fit after that, but now the door scrapes at the top ever so slightly when you shut it. Overall I'm very satisfied, since the oven is older now, but looks great again.

I watched your video on the subject and followed it exactly. It explained everything I needed to know. The hardest part was CLEANING under the stove once I pulled it out from the wall!

After searching the internet for a cause for the burner not getting hot it looked as though it was the burner switch. I ordered the switch and installed it. Behold it still did not work. I then ordered the burner, installed it and it worked. So I had a 50/50 chance as to which part was the problem. This was my first stove repair and I found it easy to do. Finding something to hold up the ceramic cooktop took the most time. I cut a piece of wood to prop it up while I replaced the burner.