EER3000K02BB General Electric Range - Instructions

1. Pull range out from wall and disconnect power cord from outlet. 2. Remove 5 screws to remove panel on back side of range to expose the bake element connections. 3. Pull push-on terminals from element. 4. On inside of oven, remove two screws and remove old element. 5. Insert contacts end of new element through the holes in oven back wall. 6. Reverse the disassembly steps to complete the installation.

This was the second replacement glass I've bought, but I'm unsure if the first one was from PartsSelect or GE directly. It was a couple years ago when I purchased the first one. The first one popped in rather easily. I scraped out the rust and debris that had built up within the lower metal track and then inserted the glass. By pulling upwards on the door handle I had just enough room to pop it into the upper plastic tabs. The second door I bought was harder. I truly feel the second was larger. I tried the original procedure, but there was significantly more glass at the top, and I couldn't push up on the handle to even clear the handle itself. I removed the glass to re-cleaned the lower track, but it was clear of debris, so that wasn't the problem. I had to completely dismantle the outside plastic frame, insert the window and put it back together. It did fit after that, but now the door scrapes at the top ever so slightly when you shut it. Overall I'm very satisfied, since the oven is older now, but looks great again.

I watched your video on the subject and followed it exactly. It explained everything I needed to know. The hardest part was CLEANING under the stove once I pulled it out from the wall!

After searching the internet for a cause for the burner not getting hot it looked as though it was the burner switch. I ordered the switch and installed it. Behold it still did not work. I then ordered the burner, installed it and it worked. So I had a 50/50 chance as to which part was the problem. This was my first stove repair and I found it easy to do. Finding something to hold up the ceramic cooktop took the most time. I cut a piece of wood to prop it up while I replaced the burner.

Installation instructions on the partsdirect site were great. Unscrewed the (2) hex head screws that hold the element and used clamps to hold the terminal ends from recoiling back into the insulation of the oven cabinet. Put the push on terminal ends on the new element, tightened screws and done. The $50. Part fixed the problem and delayed another range purchase.

Pulled the top back panel off, pulled off burner control knob, removed 2 screws which released switch, removed 5 wires from switch and connected them to new switch (pulled off faily easily). Reconnected the 2 screws to range and pushed knob back on. Replaced panel and reconnect the electric. Now works as it should.

Pull knob. Pull wires. Pull two screws. Replace switch

We emptied the bottom drawer and pulled out the stove, unplugged it and my wonderful son came over and installed the part in about 15 - 20 minutes. The part came without instructions, so we were glad he was around. I am glad we were able to find your service. Thanks.

After reading on the website of others doing repairs I was able to fix my oven easily. I removed the two screws on the back wall of the oven. I carefully pulled the element forward bringing with it the connector wires. Before sliding them off of the old element I made sure that they were pulled out far enough so not to loose them in the insulation. I removed the old element. Slid the connector wires on to the element. Carefully slid the element back into the back of the oven. Put the screws back in and I was done.

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

First I turned off the breaker to the oven, then removed the oven racks. I removed the two small bolts that hold the element to the back wall of the oven. I then gently pulled the element out to expose the terminals, with needle nose pliers I carefully removed the clips without letting the wires slip back behind the oven wall. Then I pushed the clips onto the new element and bolted it back onto the oven wall. I turned the breaker back on and preheated the oven and it worked like a charm.

Removed the power plug from the wall, screwdriver and small socket allowed me to remove the front control panel. Once I located the pilot light I pulled off the holding clips and placed a new light into the holding clips...problem solved.

Purchased the board installed it and saved about 130 dollars.

We've had this range for almost 10 yrs and while on the clean cycle the bake element burned up. We ordered the new bake element on Wednesday and was delivered on Friday. Installation was not difficult as we followed the advice of other installation reviews. However, while removing the old element one of the wires snapped back into the insulation. We had to remove the back cover plate and found the correct wire and just pushed it through. Easy, peasy, japaneasy!

There were no burnt spots on the baking element but I turned the electric power off and removed two screws and removed the two termenals wires and replace them on the new element and replaced the two screws that I removed. I turned the electric back on. Every thing is great and it only took me fifteen minute from start to finish.THANK'S