Quick Question!

Have you ever purchased from PartSelect.com before?

Models > EER3000K02BB

EER3000K02BB General Electric Range - Overview

Get Parts and Repair Help for EER3000K02BB

If you know the range repair part you need, you can browse the list of all parts on the EER3000K02BB, or you can search by name or part description. You can also find your part by where it is located on the EER3000K02BB by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for EER3000K02BB parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the EER3000K02BB

[Viewing 5 of 5]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.88

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$54.62

Bake Element - Push On Terminals - 240V

The bake element in your oven provides the cooking heat. This part can be found at the bottom of your oven, and attaches to the power source on the back wall. It has two terminals that fit into the power source receptacle. This part is made of metal, and is approximately 20 inches in length and 18 inches in width. This product is sold individually. Many of our customers have rated this repair as easy. To complete this repair, simply lift the old element up and out of your oven, and replace it with the new one. Be sure to disconnect power from the oven before you begin this repair.

$10.46

Temperature Sensor

The temperature sensor, also known as the oven temperature sensor assembly is usually found in the back of the oven. The function of the oven temperature sensor assembly is to meas...

$5.30

Rear Drawer Support

This rear drawer support comes with the installation screw. ***NOTE: There has been a factory design change and you must change both rear supports from side to rear.

$55.56

Broil Element

This broil element is found on the upper part of the oven cavity.

$26.32

Surface Burner Switch - 6" - 1560W

This switch controls the small burner on a range/stove top.

$6.98

Oven Light Socket - With Push In Receptacle

$1.63

Lens

$7.36

Foot - Leveller

Sold individually.

$18.47

Broiler Pan - Large

This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain. The grate measures 15-1/2 inches wide by 13 inches deep and the pan is about 17 inches wide by 13 inches deep. No tools are required to replace this item, simply pull out the lower drawer of your range, pull down the front of the drawer, slide the pan out and slide the new one into place. This is a genuine part sourced right from the manufacturer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven element burned itself up

  • Customer: Dennis from Bondville, VT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 216 of 233 people found this instruction helpful
Turned off circuit breaker to range.
Removed the 2 oven racks. Removed two screws in back of oven compartment. Pulled element forward and the terminal connections get exposed.
The right terminal clip disconnected by itself and the wire went back into the stove and could not be retrieved.
Removed range draw under the oven and pulled entire rang... read more

The baking assembly in the oven burst into flames one day, then broke apart.

  • Customer: Theresa from Sherman, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 120 of 124 people found this instruction helpful
After the element cooled down, I pulled the racks out of the oven, turned off the oven at the breaker box, then, using a nut driver, loosened the screws that held the baking assembly in the back of the oven, and pulled the connecting wires off. I bent the wires to make sure they would stay out, because if they get back in the insulation, they are hard to fin... read more

Oven would go in to a F2 Error

  • Customer: Peter from stamford, CT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 74 of 98 people found this instruction helpful
Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function. read more