EDW2050F01CC General Electric Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
upper rack kept falling - upper rollers no longer attached
I watched the video before ordering to ensure I had the right parts. I simply followed the video. So easy! And for less than $20, the dishwasher is repaired. The upper rack was such a hassle, I was considering getting rid of the dishwasher! So glad I found your site.
Parts Used:
-
Julie from Cicero, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would not drain completly
Remove filter screen at rear bottom of dishwasher with 1/4 in socket, remove check valve by hand, install new check valve, reinstall filter screen. Run a load of dishes, drained completly.
Parts Used:
-
Paul from Avondale, AZ
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Our silverware basket wore out.
I found Parts Select on the internet and checked out the website. Very easy to use and fund the exact part for my dishwasher. Ordering was simple and delivery was wuicker than expected. Very impressed with your service and will use again in the future as needed.
Parts Used:
-
Todd from Lake Orion, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
serious rust & corrosion on the rack
just lifted out the old one & replaced it with the new one. Couldn't have been easier.
Parts Used:
-
Elizabeth from Ames, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Water Inlet Filter
Before you due anything else...remove the water inlet valve, remove the 4 screws holding the water inlet coupling to the valve housing, remove the nylon filter (tight fit), and clean the debris from the filter. Re insert the filter, reassemble the valve housing and check for leaks. Clears most water flow problems.
Parts Used:
-
Steve from Cibolo, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
End cap broke
-
James from Las Cruces, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
replace pump motor assembly
Too easy- what made it easier was this is a portable roll-around unit I could lay on it's back. Loosen the two clamps around the washer pump, hook up the drain solenoid, washer motor wires, attach the motor hanger, that's basically it. It took longer to make sure I was working from the right set of instructions- this pump covers several models. Once I had that right, it was really a snap. Now the unit is so quiet. It once sounded like a jet engine in the kitchen, now it runs so quiet you can hear the water splashing around inside- a big improvement. We should be able to hang onto this thing for a while longer.
Parts Used:
-
Ben from Nashville, TN
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
See below
In replacing the upper rack in our dishwasher, I struggled and broke one of the end caps (see previous tale of woe. With the new end caps, I finished the job in less than two minutes with no tools. BUY END CAPS when you order a rack!
Parts Used:
-
Leslie from Amarillo, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Roller wheels in upper rack wore out
The switch out was quick and super easy. I had the top rack off, wheels changed out and rack back in in ten minutes
Parts Used:
-
Bill from Seattle, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
wouldn't drain used water
the piston and nut seal had failed so drain water would reenter the washer. i had disassemled the main pumps and manifolds to locate a failure. i replace the spray arm due to a broken retainer,and the baffles were crushed. i ran a cycle with it empty using clorine to check the repair and look for leaks,all good.
Parts Used:
-
Dennis from Franklintown, PA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Water leak on the bottom right side of the door
replaced the rubber baffle
Parts Used:
-
Daniel from Oakland Gardens, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
one roller was broken
-
Fred from Pueblo West, CO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Old rinse aid fill cap broke off at base
I removed the broken stub of the old fill cap with a screw remover. This was the only part that wasn't easy. The new cap fit fine.
Parts Used:
-
John from Corvallis, OR
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
top rack falling
watched video on website - very easy repair
Parts Used:
-
Bernadette from Contreras, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Faulty Dishwasher Door Latch
Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.
Parts Used:
-
cliff from knoxville, TN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!