ED5VHGXMB10 Whirlpool Refrigerator - Instructions

There are two tabs that hold the icemaker to the rails it sits on. I use a small screwdriver and pushed the tabs up to release the tray and slid the Ice maker out. the cover over the control motor just pops right off. Then I removed three screws from the control motor pulled it off and put the new on, replaced the screws and put the cover back on and slid the icemaker back into the rails. I shut the freezer door and within the five minutes it took me to put my tools back in the garage, it was dumping ice. Very easy to fix. You do not need to remove the screws that hold the icemaker to the tray.

removedicemaker and unscrewed 3 screws hill ding motor assembly and control module to ice maker . nstalled new part and attached it with the 3screws. reinstalled ice maker and ice making cycle began almost immediately.

Pulled out refrigertor to get access to back. lower right hand corner where water vavle located. Removed water valve cut water lines to adapt to push type fittings on new vavle and replaced vavle. Pushed water lines all the way into proper water outlet, they cannot be reversed different sizes, plugged the two electrical fittings pushed refrigertor back in place after plugging the refrigerator back in.

Definitely watch the demo video. It described every aspect to remove old unit and install the new one. Made the install 'childs-play'!!

Removed ice maker and installed new part

I watched the video and removed the tray, but there were no screws underneath it! We tried prying it off with no luck, and then I read the directions from another customer. We removed the door handle, pressed down on the dispensing unit while using a flat head screwdriver to pry off the dispenser unit at the bottom (There are two little slots where the screwdriver fits perfectly.) I was afraid of the thing cracking since it is so old, but it did fine. This was the only hard part. After this was off, the rest of the repair followed the video exactly and it was super easy and took about 5 minutes! As I was detaching the old control bracket, I saw that it was completely broken on the right side. I knew then that this was the correct fix. It was an incredible moment when we tested the dispenser for the first time and water came shooting out! Thanks for your help on this - I would have never dreamed doing a repair like this before, and now i know I can do it.

Turned off the icemaker and took out the hex screw at the back of the unit that held the cable guard. The ice maker was easy to slide out after releasing guide locks on each side of the unit. Pulled the unit forward and released the electrical connection. With the unit on the cabinet, I removed the motor housing cover. Took out the 3 scews holding it in place and the old motor was out. Just reverse the steps putting the new one in. In an hour or two we heard ice dumping into the holder.

watched the video and went very well. No problems. I am sort of handy at repairs, and found this relatively easy.

Pulled the refridgerator out from the wall . Unplugged it and shut off the water supply. Removed the rear lower panel . Removed the 2 bolts holding the bracket to the frame. Took off all 3 plastic nuts and pulled the lines out. Had to drill the bracket hole to remove it from the smaller bracket. Cut off the ends of all 3 lines. Mounted the new valve to the bracket. Pushed the lines into the new valve connectors. Bolted the bracket back to the frame of the refridgerator. Turned on the water and checked for leaks. Reinstalled the back lower panel and plugged in the power. Tried the water and everything worked now.

imakers first replaced the water inlet valve. that didn't fix the problem, but increased the water column to the water dispenser. replacing the icemker cured the problem! I now have $200 ice!!! your service was great! the part arrived as promised!

Removed icemaker, replaced motor and reinstalled. Very quick delivery of parts, fit perfectly.

replaced the motor control assembly and it works great

got new part it was easy fix thanks

First I watched the little video that was available when I bought the part on line. Though the job was easy, it was a VERY good idea to watch the video. Just makes you more confident to do the job well. The whole thing was done very quickly and to satisfaction

Istalled new ice maker in about twenty minutes.Very satisfied .