ED5GVEXVD02 Whirlpool Refrigerator - Instructions

remove contents of door-----------hardest part of chore remove top hinge cover remove three top hinge screws remove door and lay on table remove two screws holding black plastic cam piece in door, remove black plastic piece (slightly held in by some type of mastic) just pull till it comes our insert new piece, insert two screws lubricate parts mount door on hinge pin insert tip hinge pin and plate and fasten with three screws attach cover............reload refrigerator door taking opportunity to throw out old bottles and mystery jars Finis

1. Unplug the electric plug. 2 Either be in a well lighted place or get a flashlite. 3. Remove all food from top shelf. 4. Remove the knobs from both controls by pulling on them or use pliers to grab the center and pull. 5. Use the thin bladed knife and gently slip the knife under the thin plastic panel that covers the two controls and pop it off. 6.Go in back of the control panel and remove the two hex headed screws that holds the panel onto the roof of the refrigerator.7. Locate the right hand control, and use a philips screw driver to remove two philips screws that hold the temperature control body in place. and remove the wires from the terminals by pulling them with a long nose pliers.8. Locate the white panels that cover the thermostat sensor and remove the screws holding them onto the frig body. slip the long thin tube out of the plastic piece it is formed to fit.9.Draw on paper the shape and measure the deminsions,of the long thin tube. Straighten out the tube and remove the plastic covering it. Now slip that tubing over the new piece.10. Form the tubing into the odd shaped holder and gently place all of the new asssembly against the frig wall and cover with the two white panels that you removed to get to the long sensor tube. 11. Reassemble the controls in the same order you took it apart. Plug the frig back in to the electricity and set the control on 5 and it should run. Watch for a period to hear the unit cycle on and off. You are a genius and have saved at least 150 dollars.

Did you know you have to press the button next to the filter before you pull on the filter cap? Like most week end warriors, I just pulled the cap and of course, I broke it! The repair was simple, hopefully, in six months I will remember to press the button!

Removed old, replaced shelf and slid in new drawer

Just lifted out one out and sit new one in place

Looked on YouTube and found the PartSelect video. Viewed the video and replaced the part.

When my thermostat was shipped the email contained a step by step video. I just watched the video and installed it.

un-plug the power cord. remove both control knobs. pry off the cover. remove 1 screw on the right and left with the nut driver. remove two screws in back with the nut driver. remove the screw holding thermostat in place, loosen screw holding the left side of the l plate. lift thermostat up and remove two nut driver screws. remove the temperature sensing line from holding device. Remove cover down the side of refrigerator and the cover over the sensor (in back corner) carefully remove the sensor line. Carefully bend the sensor tube into the shape of the removed part(do not kink)install the new part in the reverse order of removing.. Use flat blade screw driver to press sensor line into the snaps. This was one of the easiest repairs I have ever completed.

Loosen 2 quarter inch screws on top side and remove one on bottom of ice maker lower unit disconnect wiring harness install new unit and tested Great Very easy thing to do didn't need instructions. Unit is working like new. Easy to search for parts on your web site

I followed the UTube video step by step, pausing at each section made repair very easy. Watching the video is a definite must!

snapped in new bins.

Replaced the water inlet valve. Note: although the web site shows the exact same water inlet valve, the replacement is somewhat different. You'll notice the electric prongs are facing in the opposite direction then the old one. It works like a charm need not worry as I did when I saw that. The old part is actually two parts in one. Use care when separating the front piece (it acts like a coupling where the water supply connects to and simply comes out the other side and into the refrig.) from the water inlet valve. It was a tight fit coupling that front piece to the new valve but it will fit. Make certain you purge 1-2 gallons of water before consuming any. Also dump a tray or two of ice cubes.

Exactly how the instructional video described it to be. No surprises what so ever. Ended up not being the culprit to my problem. Ordered and installed a bi-metal defrost timer. Also, extremely easy as the instructional video described it to be. Partselect is an awesome resource for knowledge and quality products with very reasonable prices.

Old water filter I twist to my left facing the refrigerator and pull out. I then remove knob from old water filter and put on new water filter. I install new water filter into slot and twist it to my right facing the refrigerator. I listen for the water surge once I heard the sound I knew the install was complete. I then place a glass under the water dispenser to filter the water to make it was clear. Done with install. Crisper Drawer with Humidity Control was very easy to install. I just slid out the broken one and slid in the new one. Done with install.

Shut off Water and Electricity. Took out the Ice Bin. Removed one bottom hex nut and then loosened top-side hex nuts (don't remove them, just loosen them) the Ice maker will slide onto the hex nuts on the side of the refrigerator.Disconnected the wiring harness from the maker. Put everything back in reverse order and Bingo! No leaks and lots of Ice.