Quick Question!

Have you ever purchased from PartSelect.com before?

Models > E23CS75DSSG > Parts

E23CS75DSSG Electrolux Refrigerator - Parts

All parts for the Electrolux Refrigerator E23CS75DSSG

Below is a list of all parts for the Electrolux Refrigerator E23CS75DSSG. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the E23CS75DSSG
1-14 of 318
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.92

Crisper Cover Support - Front

This crisper cover front support is used to keep the crisper shelf in place, and may need replacing if the door will not open or close. This part can be used for the front support ...

$4.31

Crisper Support - Rear

Replacing the rear crisper support in your refrigerator is an easy job, but to complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. This part is made from plastic and mounts on the inside of the wall. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually.

$59.10

Water Inlet Valve

The water inlet valve is also known as the water inlet valve assembly and is compatible with your refrigerator. The function of this part is to release water from the supply line w...

$8.38

Hinge Bearing

Sold individually.

$14.48

Defrost Thermostat Kit

If you find that there is excessive frost in your freezer, or the freezer will not defrost, you may need to replace the defrost thermostat. The defrost thermostat kit comes with th...

$97.59

Ice Maker with Cover - 8 Cube

This Frigidaire ice maker includes the ice mold and control device. The ice maker receives water from the water inlet valve and stores water in the ice mold until it freezes. Ice is automatically ejected and the process continues until the storage bucket is full. Your ice maker should be replaced if ice is not being generated, stored, dispensed, or the ice maker has been damaged. Replacing the ice maker is an easy job and only requires a 1/4 inch nut driver. Before you start this repair, make sure your refrigerator is unplugged. For help with this installation, check out the video below.

$39.01

Crisper Drawer Cover - NO Glass

This part contains molded glide rails for the crisper pan. It does not come with the glass shelving. The glass is not included. Must be ordered separately.

$102.90

Rear-Mount Ice Maker Assembly

This kit includes the ice maker, power cord, bail arm, and fill cup. If your ice maker is not making or dispensing ice, or you notice a leak, you may need to replace the rear-mount ice maker assembly. This ice maker mounts to the back panel in the freezer section of the side-by-side refrigerator. If you are having an issue with the arm of this kit hitting the shelf, you will have to replace the shelf. You can find the shelf by searching PS1152582. To complete this repair, you will need a 1/4-inch nut driver and a small flat blade screwdriver.

$28.41

Run Capacitor

The run capacitor helps the compressor kick on and off while maintaining a constant temperature in your fridge and freezer. You may need to replace your run capacitor if your refri...

$27.54

Door Closing Cam

Sold individually. This cam is located at the bottom of the fridge/freezer door.

$44.45

Meat Pan Cover Frame - Glass NOT Included

Glass insert must be ordered separately.

$29.53

Dispenser Crusher Housing

This dispenser crusher housing may also be known as a refrigerator ice crusher housing, and is compatible with your refrigerator. The function of the dispenser crusher housing is to shield the ice crushing blades within the ice container. To make this repair you will need a Phillips screwdriver, a flat blade screwdriver, a quarter-inch nut driver, and a pair of channel lock pliers. For this installation, work gloves are recommended. Note that this piece may look different or be a different color than the original, but this part will fit and function in the same way as the original part.

$14.33

Ribbon Cable Harness

Used in the dispenser board area.

$37.67

Crisper Glass Insert

All Parts for the E23CS75DSSG
1-14 of 318