E23CS75DSS1 Electrolux Refrigerator - Instructions

removed fan unit from frig and installed new motor and then replaced back in frig. No tools needed. need to unplug unit and take apart and put new motor in the unit and then plug back in.

Replaced the top crisper drawer frame. Installation was very easy. The hardest part was cleaning all of the spilled food/liquid items from under the drawers once removed to replace the top frame. I will keep the top frame and repair it. From what I have read, this is a very common problem as there is no support in the middle of the frame...it is only plastic.

I had to remove the face cover to gain access to the ribbon harness, also had to remove the push pads The ribbon is a delicate item so care had to be taken not to bend the ends. The ribbon can fit either side so getting it in place to make contact was kind of tricky. After the ribbon was in, it just a matter of putting things back together. Dispenser is fixed at a minimum cost, ribbon was shipped within 2 days which was great. Thanks to Part Select for easy to find on the net, had a complete diagram of the refrigerator ice/water dispenser so finding the parts needed was simple. Doug

Popped out glass, pulled up and the front of cover and pulled froward. Pushed new cover back on to studs and pushed down on cover to lock it to front studs. Put glass on top of new cover. About 3 min total to make repair.

I unplugged the refrigerator and removed the back panel in the freezer. Here the coils were covered in a block of heavy frost. The coils needed to defrost, I allowed this to happen of the course of a few hours. Once this was done I used the wire cutters, cutting the two wires to the thermostat. Doing this I checked the continuity & got no reading. Having ordered the part at a more than reasonable price including 2 day delivery, I was ready to complete the repair. Stripping the thermostat wires connected the the freezer unit, I attached the two wires color to color to the new thermostat. Here I needed to insert both ends into the connector (butt end), crimping both sides. Making sure each end I'd secure. Do this for both sets of wires. Placing the new thermostat back on the the cooper coil (on the same one it was removed from), put the freezer back in place. Here I only screwed in two, in case I need to go back in. I plugged the refrigerator back in turn the settings back to default or factory. Allowed the refrigerator to come back up to temperature for 24-48 hours. I did these and I'm glad to say my 12 year refrigerator is working just like before.

There is PG and E employee working in one of the electrical post that cause the electric surging,there is a 3 big bang then we smell burning wire.it blew and burned the compressor relay,so what i did is figure it out, all 2 refregirator fan is running the heater is working,but its not cooling, when I touch the compressor there is no vibration,so all i did is removed the compressor relay, and I found out that the wire is burned and melted the connector, i order the relay from parts select and install it.1.remove the capacitor and install it to the new relay. 2.put a new connecrtor from the wire.3. install the compressor relay.easy as 1,2,3.

Emptied the shelves off door and pulled door off fridge swet on counter and took out old plug and put new one on.

I followed the past suggestions and I opened the parts list to understand what was where. Caution when removing the face plate. The flat white connector pulls out easierly. It can be plugged back in after. I have big hands so it was hard to connect the water back to the unit. Other wise it went ok.
OH , make sure to unplug the refrigirator. I touch the control board and got snapped.

The part was easy to find on the site, instructions were right on and it only took 25 minutes to accomplish with just a screw driver and a pair of pliers.

Removed Water drip tray, Then removed (3) screws holding the cover in place. Removed (3) more screws holding the circuit board in place. pulled out ribbon cable from the circuit board which is connected to cover, and put aside.
Tried to remove screws holding actuator in place, but it was a bit tight,,wish i would have tried to un-plug the connector on the left side first, but did not, i instead removed the water tube to gain better access,,,,replacing actuator was easy, re-attaching water tube was not simple at all,, but if you do end up pulling it out,,,do not waste time trying to pull it back thru, it is not nessasary, and impossible to do,,the end is tapered, and makes a pressure seal, so it will not leak,,,re-attached screws, ribbon cable, cover, and drip tray,,and done.

took door off(very easy two bolts on top)lift door replace parts

I broke off remainder of clip, and used phillip
screwdriver and pushed pin into wall. I lined up new support and pushed in peg to secure

First I obtained the manual to the refrigerator. I identified the screws to be removed. I turned off the water then unplugged the water lines. I then replaced the Water Filter Base and reassemble the parts. Within minutes of turning on the water, water and ice making had returned. I was a hero for saving the family $200 in parts and labor.

Pulled the unit out from the wall and with a flat head screwdriver and a utility knife I replaced the valve assembly. It was no problem at all.

After taking the complete motor, tray, icemaker, etc out and finding no problem, I then finally checked for power at the connector at the top of the icemaker. I concluded that there was no pwoer going to the motor. I then removed the circiut board and found the relay for the auger was not working. Putting the new board in took 10-15 min. and then the auger started to work.