DWUA601AAE Admiral Dishwasher - Instructions

Followed the outstanding video instructions. Your company is fantastic. Your attention to detail, the quick shipment (one day) and video ... stellar! We will be referring your company to all!!! Thank you!!!!

replaced with new gasket and it works great.

Hand tightened nut

Received the parts within two days. Watched the video and it explained everything. Found it hard to believe how easy it would be, and it was very easy. Cleaning up the door in preparation to installing the new gasket took longer than the gasket installation. The gasket just pressed in the channel, frankly I was surprised that the door inner shield did not have to be removed. The water deflector just pulled off and slipped on (probably took 30 secends. Ran the dishwasher a few times, and no leaks. They had cited that the majority of leaks were due to the gasket, and it was right on. Like the dishwasher and can go for another 12 years.

Followed the video on the websight

Because mine is a portable dishwasher, I had to remove top first. the sides and back are one complete unit. the torque screws are in the front, 2 on top, and 2 in rear. Then the panels can slide back to access the spring. Replace the plastic piece & hooked on the spring. Reassemble in reverse order.

Well, I haven't gotten the right part yet. I'm such an idiot that I've ordered the wrong part twice now. So, figuring that 3's a charm, I'm going to try to get the right part now. I do have to say that part select has made it amazingly easy to return the parts. And both of the first 2 (wrong) parts arrived within 2 days of ordering. I'm pretty impressed with this company. Now, if I can just order the right part, I can tell you how the installation went!

Followed the video found on the website. Very simple repair. Saved $120 by getting the part and fixing myself.

I pulled the old rubber gasket off put the new one on and then took the back end of a kitchen knife to push it in all around the door to create a solid seal

First problem was finding out whether Dishwasher had power at all, since nothing happened when you tried to start it, and I really didn't want to have to pull it out and disconnect the power cables at the box on the back of the dishwasher. Used the video instructions from PartSelect and opened the inside door panel and exposed the switch, then put a continuity tester (light with two prongs) across opposite sides of switch (white one side, black the other). With the test light on, knew I had power and was able to locate circuit breaker to turn off power to dishwasher, all without dismounting it from the cabinet at all. From there, followed the video. Hardest part was disconnecting wires from the old switch, which was slightly corroded. Plier trick on video didn't do it, and had to use large screw driver blade to carefully lever wires off of the switches. NOTE: Look at the new switches before doing this, and you'll be able to visualize how the wire clips slip on the switch connectors. Great site, and dishwasher started right up after the repair.

Emptied diswasher. Extended the upper rack half way. Sprayer bar had already fallen off. Unscrewed the "bearing nut", replaced the "bearing nut" with a new one, pressed the new sprayer bar on, then closed up the diswasher. Hasn't fallen off since. An easy job even for a novice.

First I turned off the fuse and h2o, then replaced the intake valve. This was tricky b/c there is very little room underneath to maneuver the wrench. I had my son watch to see if h2o came out of the intake hose while I turned the h2o on and off from the main valve. Knowing I had h2o, I replaced the intake valve and turned on the machine. Still not working properly. Next, I ordered a new float and fill switch (the little computer chip looking thing). Replacing those was a snap. Remove a couple screws, replace the switch, screw back in place. The float was even easier, using pliers, I removed the nut from the float stem underneath, then simply pulled out the old float and dropped in the new. While keeping the door slightly ajar and holding the float down in place, I pushed the securing nut back into place. Again, I started the dishwasher, and again it did not fill. Frustrated, I removed the intake valve again. I used a wooden skewer to pull out some sediment that had been in the intake line (my son did not pick up on the irregular h2o flow during the initial test). Put the valve back in place again and viola, it works perfectly!

I didn't have a clue how to fix this dishwasher so I did a search for Maytag parts and found your site. It looked like the door switch was the likely problem. I watched the video that Steve did showing how easy it is to fix and ordered the parts. I got the parts in the mail a couple days later. I did the repair in about 15 minutes. Just pulling the connectors off the old switch took some strength, just like Steve said. Put the switch in and back together and bingo the dishwasher works like new. Thanks Steve and PartSelect!