DWUA201AAE Admiral Dishwasher - Instructions

Took out screws on inner door(door part #8), being careful not to let the door swing upward once the screws were removed. Then removed bar reinforcement (door part#9). Next removed the control panel barrier (control panel part #6). Took picutre of items to be removed. Next removed the wires from the door switch, had to use needle nose pliers. Removed door switch&latch handle. Reassembled parts using old "foam". Easy. Total cost: $34. 49 Vs a quoted price of $160-200. 00 For service&parts.

Took the handle off the old basket and put it on the new one and it was done.

first i unhooked the 2 hoses then removed the 2 screws holding the valve in place, I then removed the hose fitting from the old unit and installed it on the new one. I then bolted on the new valve and reconnected the hoses and it worked fine.

Removed the rack from the dishwasher.
Took off the adjuster from the rack using the allen wrench.
Replaced the new.

Perfect

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.

Actually following the online video is the way to go.

Took off the lower front plastic piece and unscrewed the side panel to snap the new part in place then attached the spring to it.

USED A STAR SCREWDRIVER TO REMOVE THE LOWER SCREEN THEN REMOVED THE SUPPORT NUT BY HAND REPLACED THE LOWER SPRAY ARM & SCREEN WORK BETTER THAN EVER.THE ONLY NEGATIVE WAS THE PART TOOK 10 DAYS TO ARRIVE .

I disconnected the dish washer and pulled it out. I laid it on its back, unplugged the electrical wires,removed the electrical magnet and pried the shaft seal out with a flat screwdriver. I gently packed the new seal into place with the flat screwdriver. I connected the electrical magnet and wires. I then installed the dish washer and ran it through a cycle. I am pleased to say the dish washer does not leak now.

Turn off power, remove the lower kick plate and lower trim panel with the nutdriver. The float switch is in the front on the left. Remove the two wires on the switch. Use a #1 philips to remove the one screw holding the switch to the frame. Remove switch. Install wires on new switch and install switch using the screw. Be sure to get the plastic float arm under the switch. Raise float and observe the switch clicking on and off. Replace lower plates and restore power.

***BEFORE STARTING BE SURE TO TURN OFF THE POWER!!
THE SPRING TENSION WAS GONE THAT WOULD KEEP THE DOOR FROM FALLING. KEEP IN MIND THERE IS A DOOR SPRING AND LINKAGE ON BOTH SIDES OF THE DOOR. SO BUY 2 OF EACH AND RETURN THE ONES YOU DON'T USE. IF YOU REPLACE THE LINKAGE ON ONE SIDE YOU MIGHT AS WELL CHANGE THE OTHER ONE SINCE IT'S ONLY A SMALL PLASTIC PIECE.
FOR ME THE SPRING WAS GOOD - ONLY REPLACED THE LINKAGE. REMOVED THE PANEL AT THE BOTTOM AND THE 2 SCREWS THAT HELD IT UNDER THE COUNTER TOP. I DIDN'T DISCONNECT THE WATER BUT WAS ABLE TO PULL THE UNIT OUT JUST ENOUGH (10 INCHES OR SO) TO GET TO THE SPRING. HELD IT IN PLACE WITH THE VISE GRIP SO IT DIDN'T FALL BEHIND THE UNIT. FYI - YOU MIGHT HAVE TO ADJUST THE TENSIONER ON THE BOTTOM IF YOUR SPRING TOOK A WALK WHEN THE LINKAGE BROKE. BE CAREFUL PUSHING THE UNIT BACK UNDER THE COUNTER. TOOK ME ABOUT AN HOUR AND SAVED SOME MONEY

ordered new gasket, watched the video that was in the order conformation on how to install which was very easy to understand. the actual installation was right on the money. Thank-you.

Kill power to unit. Lower door. Hold down door and remove inner plastic door cover torx screws, rotate up and use inner door cover to brace outer spring loaded door from closing. lift off metal strap that runs along top edge of door. Unsnap black plastic cover.Latch is under cover. Unplug wires with pliers (they just pull off) after noting where they go. Unscrew single hex head screw and remove latch assembly. inside latch will be reused with the new latch switch holder. Pry up plastic clip keepers and remove inside latch. Depending on age they might break, no big deal you will use the new holder anyway. orient and install switches into holder, install inner latch and install assembly back onto door. Install wires, cover, metal strip and inner door in reverse order. Very easy to do. Parts worked perfect.

advisor showed a 30% chance that the part in question would solve my problem and it did. Had help from my 12 year old so it was a great teaching moment. She particularly liked when I forgot a part in final installation and she had to remind me to install before closing up the repair. 15 minutes total. Awesome fun!