Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Turn table on microwave would not turn.
Removed 6 screws from the front and back of the bottom of the unit. 3 screws each side. The panel will swing down. Remove the wires from the motor. Remove the one screw from the old motor. Insert the new motor and reverse the procedure. DIY will save you a $ 95.00 GE repairman labor bill, plus the cost of the motor. I repaired the problem for less than $25.00!
Must remove 5 screws in bottom of Microwave, which is hinged to the unit. Then simply remove the old lamp holders, and replace with replacements. Uses only a single screw for each lamp.
the online instructions were ideal - just unscrewed the right-hand screw (the only screw) and replaced the bulb by inserting gently but firmly)...getting the old bulb out was a pain, b/c it shattered in my grasp (with little bits of glass all over the stove!), but that has nothing to do with the purchase and installation from this site - all a very good experience
original grease filter fell apart while washing it and couldn't be put back together
Can't believe GE Profile allows such a flimsy filter to be used at all. These filters should not just fall apart while running water through them.
I ordered replacement 4 replacements because I'm sure this will happen again. Part Select fortunately had replacements! You just slide the new filter in place, no tools required. Thanks Part Select.
The replacement of the light no problem, the reason the light broke; problem. The original was glued in (for transport i think) and simply trying to unscrew it out (in a very tight slot) it broke; be careful or you’ll be buying a new $20 bulb (with shipping and handling).
First I removed the screws that were underneath the microwave. Once I did that I disconnected the wires to the bulbs and removed the screws that were attached to the holder lamp. replaced the parts and reversed the process. It went really smooth.
Un screwed the cover but when i tried to remove the bulb it was broken at the base. I disconnected the power and used neddle nosed pliers to remove the base
Micrwave won't run - turntable turns backwards when door opened...
Most of the effort is simply getting the oven out of the built in enclosure and the sheet metal off. This take about 15 minutes then you have to remove the two screws (not handy location) that hold the door latch/switch assembly so you can remove the switch. I did this BEFORE ordering so I could test the switch (it was charred) and verify the part needed. WATCH OUT - some ovens use a normally open an some a normally closed version of this switch - you have to get the right one. I checked several suppliers that were showing the WRONG switch for my model. PartSelect had it right. Once I received the switch I had it on and the oven installed and running in less than 30 miutes. Working fine since then...
Ordered through parts.select because GEprice was totally outrageous. Unfortunately, my first order was lost and after 2 weeks I phoned your customer service and Betty was quite helpful. She followed up (as I called on a Saturday am) on Monday and reported to me that the item was lost. She then asked me if I wished to place another order. I did, of course - it arrived in a timely manner - I placed the cooking tray into the microwave and I was in business!!! Thank You Partselect!!!!!
I replaced the switch at the bottom per instruction. I had both switches. I think it was the monitor door switch.It works fine now. Thank you Part Select .
Microwave does not have power at all, though outlet has power
unplugged power cable / unhooked front vent / unscrew the monitor panel / slide up to dislodge / take the fuse out and put in the new one in / fuse is located right in front of monitor panel once its open might be covered by wirings / you can unpin the cables from the panel to make it easier for you just make sure to put it back properly or you can have somebody hold the panel for you. Installing the fuse is easy waiting for the parts is crazy......
Took the front panel off, played with the switch while it was plugged in to verify the switch was bad. I actually was able to tweak the switch just right to keep the microwave working while the part was being delivered. When it came it was just removing two small screws and replacing. Very easy.
