DU1000CGZ1 Whirlpool Dishwasher - Instructions

Installed the new upper spray arm mount. First I installed it backwards which made the blades not turn freely (rub against top rack basket). Turned it around and was good to go. I found it helpful to remove the top basket in order to do this. Note that this clip is gray while your dishwasher tines are white. This does not cause any harm.

Simply removed deflectors and gasket, replaced all , took all of 5 mins. workes great now.

Removed upper basket and installed the arm. New snap in didn't require phillips screwdriver as old one and new support had split to insert. Replacing upper spray spinner dropped screw down around pump. This caused misery unassembling lower covers to receive Stainless
Steel, so magnet won't help ended up with mirror and hemistat to reach through large screen figures. So make sure to put towel or something in the bottom to catch parts.

unscrewed sprayarm, removed bearing and seal, used PartSelect pic and description schematic to identify part numbers then placed order. Parts arrived in two or three days.

i took off the kick plate and found the water valve. its the piece that water comes to from under the sink to connect to the dishwaser. it has a plug with 2 wires. i turned off the water supply, disconnected the wires(probably should have flipped the breaker but didnt) took out the 5/16 mounting screws, had to use a little end wrench on 1 because it was behind the water line and a nut driver on the other. i put some thread gook on the connection and put the new one in the way it was and it works great. i am writing this because thats where i got the info to diagnose in the first place and saved me $$$!

After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.

first I removed lower basket. then removed lower sprayer attached to pump housing by unscrewing the cap by hand. the I removed the pump cover . there were six alan screw two of them were missing causing the failure of the seal spraying solution at the door. replaced the pumpseal working backwards until everthing was replaced.

Removed one screw to get the spray arm off the rack, one other screw to disassembly the spray arm assembly. Replaced worn and damaged parts. Installation was reverse order of disassembly.

actually my wife did the repair. she unsrewed the water sprayer and removed it, then unscrewd the star key screws and then replaced the seal. she put everything back the way it was and it is now ready to use and we no longer have the problem.
just a suggestion...if you take some baking soda and some vinager you can clean the drain out. just simply poor in the soda and then the vinager.and it will fiz cleaning your drain.

I was hesitant at buying the Matag made replacement, especially since it was one piece as compared to my 10-year old 3 piece assembly, and my dishwasher is KitchenAid.
Ordered on a Sunday afternoon, had in hand Tuesday same week, one phillips head screwdriver to remove/replace. Everyone smiling!
Did not need to remove upper rack. Simply unscrewed 1 screw, put on new one-piece arm, replaced with same screw.
15 minutes!
Good price/delivery.

Removed the rest of the broken retainer plug. Part number was on the top of the plug. Went to Partselect.com looked up the part and ordered it. The right part (important) arrived in a few days. I put the arm back in place, screwed in the new retainer plug and we were back in business. Cost of part about $5.00. Price of not having to share in cleaning the dishes, priceless. Any future problems with any of my appliances, this is the first place I'll look for the needed part.

Pretty simple. Hardest part was working the end clips of the slide to remove top rack. You simply need to squeeze the plastic clip in to slide it out. Once the top rack is out, it was an obvious philips head screw removal and new part replacement.

1-remove upper rack by removing holding clips.

2-remove old assembly from Rack

3-cut old ring guide to accomodate new style (one solid plastic piece) and reglue after accomodating new assembly

4-re-install upper rack

DONE

I removed the screws on the door cover and snapped in the new clip

for the arm I just removed one screw and replaced the arm

replaced spray arm, but this did not resolve the problem. The troubleshooting guid (inside kick panel) indicated the check valve may be stuck. We had quite a bit of lime build up, so I suspected the loose deposits may be stuck. I removed all of the deposits, disassembled the lower unit.
Removed lower spray arm, removed spry tube. The tube is two pieces. first the upper portion must be removed (two screws-place towel on base of tub to preven screws from falling into the chopper area), and then the lower portion simply rotates clockwise 1/8 of a turn. The attachment for lower spray arm has a small plastic bearing, careful not to drop it.
The dishwaser then had to be pulled out and turned on the side. I removed the entire lower unit by removing the white tabs (3). Careful, because the unit is now free to drop into the tub. Next I removed the pump. This is tricky as you have to remove the aluminimum bracket to get to the mountin bolt. The bolt turns out easily w/socket and extension. The pump motor is then rotated counter clockwise, and pulled from the pump. Takes a little force as the gasket makes for a tight fit.
I then removed the choper / pump unit from the basin. The build up behind the chopper screen was extensive, so I had to remove the screen and then the chopper cover. After cleaning, the check valve was unplugged and I reassembled the unit.

Dishwasher works great now.