DTH18ZBSBRWW General Electric Refrigerator - Instructions

I pried the relay from compressor with small screwdriver, cut and replaced burnt wire going to relay,pushed new relay on compressor and wires unfortunately it did not fix the problem.

Removed glass shelf, cleaned and set aside. 2 screws attach the old bracket, one on front, one in rear. Removing front screw requires popping off cover on front of shelf. (gently) Scrub off accumulated gunk. Install new bracket reusing same screws. Place shelf in fridge, making sure bin divider is attached to shelf with open end to front so that bins can slide into place. Slide glass shelf top back in place, do this gently, does NOT require force. Pop front shelf cover back on. Gently slide in bins. Done.

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

This was after sitting idle for 9 mos. I simply pulled the part, ordered the same part and installed. Nothing more than a couple of screws and 2 wire connections. It now works great.

I must thank yo for sending the fan so fast. If I ever have to deal with any appliance again, you are first on my list.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

Remove fan, unplug parts, plug in new parts replace fan. DONE

got on part select web site and found other customers that had same problem and on their site they had comments from them to fix problem. I then took off back panel on frig where compressor is by removing 6 screws and found the relay attached to the compressor then pressing down on holding spring removed 2 wire alligator clips and it was bad ordered one from part select put the new one on an frig was fixed. entire fix took about 30 minutes from isolating problem to fixing it. thank you part select

I pulled off the plastic strip that says “ vegetables” on one side “fruit” on the other. That exposed screws on the left and right sides. I unscrewed both sides I did the same to the back support arm put the new arm in and it works great! The man who helped me at part select was so patient and so kind and helping me select the right piece to begin with to make sure I had the right model number. Could’ve had a better experience with the repair company. Tammy Peterson

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

i took the backing off with a screwdriver, cut the wires and put the 2 wires on that came with the thermostat. p.s. make sure you pull the power plug before you start.

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

easy - replaced it

i am totally impressed with your company how effective it is.... i will go to yours if anything is broken or replaced

thanks

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil