963864-1-M-GE-WR09X10106-Overload-ptc-5-speed.jpg
963864-1-S-GE-WR09X10106-Overload-ptc-5-speed.jpg 963864-2-S-GE-WR09X10106-Overload-ptc-5-speed.jpg 963864-3-S-GE-WR09X10106-Overload-ptc-5-speed.jpg

Overload/ptc - 5 speed

PartSelect Number PS963864

This part helps protect the motor from overheating.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Will not start.
  • Compare At

    $27.13
  • You Save

    $4.52
  • Your Price

    $22.61
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.6 / 5.0, 5 reviews What's this?
1-5 of 5
 

12 of 14 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

Customerjim from buckeye AZ

It quit working-refer-freezer-part,fan keeped running

pulled out switchs verified part #'s-ordered replacements- its actually plug in switches and very simple

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 14 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerJoel from Childress TX

Condensor fan out of service

The only part that I should had used was the condensor fan motor,which it was so easy to remove,and instaled the new one,then replaced the missing parts and problem solved. The technician before me,declare the unit a total loss,there for after doing that, he took the rest of the parts with him for his own benefit. The repair was with no difficulty,and time spend around 20 min. Thanks.PartSelect,your delivery and easy way to place an order is great. Thanks. Joel

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Overload/ptc - 5 speed

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customerphillip from hartselle AL

Overload switch failed on compressor. No cooling

Unplug. Remove back cover. Remove retainer (simple wire clip) from overload. Unplug overload from compressor. Remove two power wires (if stabs are tight you might need pliers). Note which wire goes where. Remove capacitor from overload (just pul it straight out .. Pull hard or pry a little with screwdriver. Insert capacitor into new switch. Reattach wires to same place in switch. Insert switch into compressor. Replace retainer clip. Replace rear cover with original screws. Plug in. Cool!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerJoyce from Barns City IA

Freezer not working

Remove fan, unplug parts, plug in new parts replace fan. DONE

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Overload/ptc - 5 speed

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

Customerken from fulshear TX

During hurricane ike, frig. Saw several inched of saltwater and sand underneath. After cleaning up, I tried to run and only the blower fan worked. It must have been just above the water. The compressor did not kick on. I looked at the lowest elec. Connections and saw corrsion on the overload protect

This was after sitting idle for 9 mos. I simply pulled the part, ordered the same part and installed. Nothing more than a couple of screws and 2 wire connections. It now works great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5