DLW - Instructions

Move washer to area with plenty of room. I took mine out to the deck. take off front of cabinet remove back panel, remove old springs, (a bit hard) remove belt, lift out tub turn over and loosen screws do not remove!! remove old snubber and replace with new, Not bad. Put tub back in washer put on new springs(didn't think I'd ever get them on, not enough upperbody strength)Video would have been priceless!
reattach belt and panels put washer back in place. No noise upon spinning but I now have issues with the agitator, Need a new washer!

I was doing laundry one day, and noticed that the washer did not drain. I drained the water via a shop vac and checked the hoses. There was a baby sock stuck in the hose leading to the pump! I cleared the jam and the washer finally drained again. Once I ran another load, the washer wouldn't drain. I repeated the procedure, and found that the motor was spinning but the pump was not working. I disconnected the machine and proceded to remove the pump. I found that, due to blockage, the motor had reamed out the housing that turns the pump. So, at the advice of my father, who has used this site for other repairs, I entered the model make and number. I was able to view an exploded schematic of the washer in order to correctly identify the part I needed. I found the part, ordered it, and it came to me in about 2 days. I replaced the pump, and my washer has worked great ever since. Thank you PartSelect.com.

These gaskets and seals were relatively easy to get to. I replaced all 3. Put machine back together, but washer still leaked. I ended up having to remove more components down along the center shaft towards the transmission. I found that the "tub seal" was worn out. I also replaced the "seal nut assembly" and "O-ring" while I was at it. The seal nut and tub seal were more difficult to remove without the proper tool, but a bigger rubber mallet and strategically placed pliers were enough to break them loose. Once all parts showed up the washer went back together easily and it is now leak-free.

I unplugged the electric power cord and disconnected the two water hoses and the drain line from the wall. It was messy as water leaked from the disconnected hoses. I tilted the washer forward and leaned it against a bench for support. This exposed the bottom of the washer from the back. I removed the v-belt from the three pulleys. The motor mount was spring loaded making it easy to remove the v-belt from this pulley first. After removing the v-belt, I then removed the 4 screws to the small plate on the back of the washer to gain access to the water pump. I then removed the two water hoses from the water pump using vice grips to squeeze the clamps and slide them off of the hoses toward the water pump. After removing the two hoses (a little messy again), I removed the water pump by using a socket ratchet to loosen the four bolts. I replaced the water pump with the new pump and then reassembled everything in reverse order.

This was easy except for the e-ring which was extremely difficult to remove. When I put the new one on I filed down the bottom of the front edges to make it easier to slide it on. Beware: If you have the washer tipped back against the wall when you do get the e-ring off everything will come sliding off the shaft all at once and go everywhere. These parts are covered with black grease and made quite a mess so you might want to have someone hold them in place so you can gently slide them off one piece at a time.

First I disconnected the hoses and moved washer out to a larger area. Washer had to be completely torn down. Took front cover and casing off. Took all electrical and plumbing fixtures out. Removed the drum hold-down springs. Removed the drive belt. Inverted the drum/agitator section. Removed the drive pulley and bearing assembly. Removed the brake snubber. Removed the brake shoe. Reinstalled new parts. Put washer back together. It now works great.

I took out all the tubs and the apparatus holding the gear and thrust bearing assembly. I used a homemade tool (long zipties) to pull the springs off and to put them back on. After that I just replaced the thrust bearing with the new kit and put everything back together.

By sliding the machine out away from the wall I tipped it back so that it set against the wall on an angle enough for me to work on the bottom. I removed the belt and drive pully. The brake stator can be removed from the bottom if drum is centered. The brake is under pressure from a big spring in there that applies the brake. Replacing three of its mounting screws with longer ones (10-24 x 2) allows you to let pressure off of the brake spring slowly. Replaced brake rotor and stator and compressed spring with long screws as in removal. Replaced all original screws to hold in place. Installed pulley and belt. Works like brand new, all for about $30. I bought the snubber also but did not realize that this is not part of the brake. I little confusing on the parts drawing.

All went well 1-remove front panel 2 screws 2-remove 2 front springs tilt tub 3-forward bottom out 4-remove pump 3 torx screws 5-r and r belt pulley and spring reassemble fast service as well thank you

I tipped the washing machine back to allow me access to the bottom of the washing machine to remove the belt from the water pump. After removing the belt, I righted the machine, unscrewed the three screws holding the rear access panel on. I used pliers to remove the clamps from the inlet and outlet hoses then removed the hoses. I removed three screws holding the water pump on to the bottom panel of the washing machine. I removed the pump and replaced it with the new pump. I then reinstalled the screws, the hoses, the clamps, the access panel, and the belt. I plugged the washer back in and - viola! It works again.

I took pictures at different steps in case I forgot how it was assembled. Unplugged the power, turned off the water hoses, unplugged the hoses, pulled the washer out, took of the access panel in the lower left hand corner, took of two tec screws that hold the water valve in place, removed the four wires that were attached to the water valve, removed the water hose attached to the water valve, reattached everything to the new water valve. The only difficulty is the access panel is a bit small

to replace the seals is the easier part of the job. I Removed the front panels and removed the front screws for the top and opened up. Then you have to remove the agitator, then the bell plug, the bolt holding the bell along with the bell, then the 1-1/2" nut under that. then slide the plastic washer that fits into the splne. to remove the drum you have to remove the plastic top to the drum assembly. Then you can remove the drum along with the along with the alumunum splined hud that is atrtached the the metal drum. Before removing the drum the seal under the plastic washer mentioned above needs to be removed. once the drum is out you can in bolt the aluminum splined hub from the metal drum. The outer plastic drum has a seal that is glued and slides over the vertical flange. The glue is not included in the kit. once the botom seal is installed. install the new aluminum splined hub to the metal drum. install lower seal to botom of the splined hub. reinstall the hub. once the large nut and plastic spined washer is installed. The top seal neds to tapped onto the hub agian with an object that matches the dia. of the seal flange. the n install the bell, nut ans plug. The bell does not like to align to the splined shaft, do not force it. reinstall the agitor an assemble the rest.

I first unplugged the washer. I removed the 2 screws that hold the front panel and removed the front panel, they are located at the very bottom outer edges of the front panel.
I then removed 4 of the large springs that are attached to the drum, this washer has six but I only removed the front 4. Removed the two hoses going to the water pump and drain hose, removed 4 bolts that attach the motor to its mounting bracket. Unplugged the wiring harnesses going to motor and what looks like a capacitor mounted to the side of the motor.Then I removed the drive belt. ( when the machine would first start to spin it would make a clacking noise which ended up being a chunk out the the drive belt causing the belt tenshioner to slap causing that noise and letting the drum spin during the wash cycle. So far very easy. I then removed the motor and when it is disconnected you can then remove the water pump. Three hex head bolts need to be removed and it pulls right off. I then removed the six bolts that hold the brake pads in place. I applied silicone grease to the new brake pads and installed them. The pad at the back of the drum was very hard to line up with the holes. I used a very small screwdriver to line up the disc brake mounting holes to get the bolts started and it worked fine. I then put it all back together and it works great. I have to add that I have been an auto mechanic for 28 years and not to brag but this is not your average repair job.

The problem was not in the switch but in the plastic hose from the tub to the switch. The hose was cracked and air/water leaked which therefore didn't activate the switch. I removed the top back cover to access the switch and released the hood of the machine, like a car, using a thin scaper to depress the spring loaded retaining clips. The hose was cracked at the tub just above the retainig clip. I bought new hosing at a local hardware store and replaced the switch to omit both of them as a future problem. Sell the tube with the switch as a package deal? Damage to tube may occur from violent, out of balance, spinning tub on spin cycle.

Tried to remove brake stator with machine tilted back. Thisforced the stator off center. Removed the 6 holddown springs, water level hose and drain hose. Pull drum & transmission out of the case. Placed the drun on the ground, brake facing up. Replaced the short screws on the brake stator with 2" screws one at a time. Caution the spring has 200 lbs of force. Used 2" screws to back off spring. With spring tenshion released replace parts. Reversed proceedurer. Machine quite. Wife is happy.