DE8600 Dryer - Instructions

Removed front of Dryer, using screw driver and putty knife to push in the top clips. Front drops down. Disconnected wires to heating element. Then removed whole heating element chamber. Removed old heating element from chamber. Then installed new heating element insude of old chamber. Reinstalled chamber in dryer. Hooked up all wiring. Note! Dryer "must be unpluged" before starting any work! Last step reinstall front of dryer. Repair complete!

This is hardly a "repair". You toss out the old lint screen and put the new one in. The hardest part was getting the lint screen out of the plastic bag it came in...

ta da it is done...

From previous experience I suspected the thermal fuse. Turned off the power and removed the front of the dryer by removing the two philips head screws in the door hinge and the two screws on the opposite side of the opening. The front came off easily since all that holds it in place besides the 4 screws are two spring clips. The thermal fuse is located on the side of the chamber enclosing the heating element. I removed the wires connected to the thermal fuse and temporarily joined them together with a spade type connector in order to determine if the thermal fuse was the problem. Turned the power back on and tried the dryer......it ran normally. Turned the power back off and removed the thermal fuse by taking out th two screws with a 1/4" nutdriver.
Ordered a replacement thermal fuse, installed it (with power turned off) and put everything back together. Dryer functioned normally after the thermal fuse had been replaced.
The thermal fuse can be removed and reinstalled using a 1/4" nutdriver. The wires are connected with push on spade type terminals.
Note: The swing damper on the dryer vent (the hooded cover where it exhausts to the outdoors) was jammed in the closed position with an accumulation of lint, which caused the dryer to overheat and blow the thermal fuse. If you experience a blown thermal fuse, always look for the cause or you'll blow the replacement within minutes of running the fryer again.

remove the rear lower left vent cover to get access the belt tensioner and pulley. then pop the top section up with a flathead screwdriver in the front, freeing it from the popclips. Then remove two screws from the back side of the front section releasing the drum. loop the belt around the drum.

Turned off circuit breaker. Removed two screws at base of front panel with stubby Phillips-head screwdriver. Swung panel up about 30-degrees, and removed panel, disconnecting red and yellow wire to door switch. Removed four sheet metal screws and took off large drum support bracket. Checked drum support rollers and shafts. They were fine. Reset circuit breaker and turned on dryer. Rattling noise still present.
Removed six small screws holding blower fan assembly. Shaft receiver on squirrel cage fan was worn completely round (it should fit onto a half-round shaft). Ordered new blower fan from PartSelect.com. Replaced tonight, and it works beautifully. This dryer is 29-years old. All it's ever needed in the 10-years I've owned it is a belt replacement and this repair. Long live the 1970s Maytags, and good parts suppliers like this one.

Removed the screws and took the door off then took the front panel off and popped up the top. Then pulled the drum out. Took snap ring pliers and removed rollers and replaced with new rollers then vacuumed all lint from machine and reversed operation to put everything back together. Operation was a total success!

1st I pried the dryer top open then disconnected the two wires for the auto shut-off. Removed four nuts with driver that opens front and releases dryer barrel. Lifted front up a bit to remove from two lower tabs at bottom of unit and put aside.

I then slid the belt over the barrel noting the side up directions on the belt. On the lower left on the back of unit I opened up the vented cover to reveal the motor pulley and belt tension pulley. I put the belt on the pulley and brought the belt tension pulley over the belt. I then aligned the belt to the proper point on the barrel and reattached the front being careful to center the barrel onto the rim that is built into the front. Take care to align all the tabs and shims in the correct order so that barrel rotates freely. Replace auto shut off wires to switch on inside of front and close top.

First I removed the two screws from the dryer front cover (located just under door)I Then swung font cover up and off it's latches. Exposing drum asy and heating element. Using a nut driver to remove two hold down screws and disconnect electrical wires from heating element. Really simple! took me approxmatly 20 minutes and this included vacuuming inside motor area with a shop vac.

First pry up on the front edge of the top panel of the dryer which is held in place by snap in clips. Pivot the top open and support against wall or other taking care not to pull on wiring harness. Next remove the 2 screws that hold the front panel in place. These are located on the inside of the front panel. The front then snaps loose also. Remove the plastic drum stop located at the top edge of the front of the dryer. Next I removed the 3 drum screws located inside at the back center of the dryer. Next you can you need to remove the belt the motor located at the rear vent panel on the back. Slide the now loose drum out exposing the rear bearing. With a 5/16 end wrench, loosen the 2 screws on either side of the bearing retainer. Assemble the new bearing bracket to match the old one. Apply a liberal amount of supplied lubricant to the pivot ball and plastic retainer. At this point it was helpful to have someone at the rear of the dryer hold the new retainer bracket against the back of the dryer while I tightened the new bearing assembly in. Assemble dryer in reverse.

First I unplugged the machine. I removed the two screws in the front panel and tilted the bottom of the panel out unclipping it at the top. I removed the lint duct whichis held in place with several 1/4" hex head screws. Then I removed the blower cover, also held on wth 1/4" hex head screws, exposing the blower wheel. Using snap ring pliers I removed the snap ring at the end of the motor shaft. Using needle nose liers I removed the spring clamp around the center hub of the old blower wheel and pull the blower wheel off the motor shaft. After cleaning as much lint out as I could I put the new blower wheel on the motor, secured with spring clamp and snap ring. Then I put the blower cover and lint duct back on and put front panel back on.

Followed the instructions on the video, and saved 500 hundred dollars. I was already shopping for a new dryer. Thanks so much!

Opened front of dryer & watched the heating unit not shutting off. Purchased the proper high limit thermostat. Replaced it and the multi-temp cycling thermostat for good measure. My dryer runs like new with no additional problems. Thanks for making parts so readily available. Thought I was going to have to replace my dryer, but now it's fixed.....Thanks,again.

Replacing the blower fan took way too long, like 4 hrs, because I didn't know how to disassemble the dryer and get to the problem. Replacing the idler bracket and assorted retaining rings and washers was fast, something like 1 hour. Disconnect the power cord, exhaust hose, and gas line. Remove two screws at the bottom of the face of the machine, unplug the electrical harness to the door light, switch and ground and remove the front of the machine. Remove the access panel at the back of the machine and remove the belt from the idler pulley. Remove the four screws holding the front drum support assembly and remove the drum. Replace some old retaining rings and the spring washers on the drum support rollers. Around back assemble the idler pulley assembly with some new washers and the old roller which seemed in good condition. Put it all back together. About one hour.

Unplugged the dryer!!!! Removed two screws from lower front panel. Pulled bottom of front panel forward which allowed clips holding top of panel to release. Unlcipped wires attached to door switch on front panel. Set aside front panel. Removed 4 screws(2 on left & 2 on right) from the drum retainer ring. Set aside retainer ring. Removed thin metal cover protecting blower wires. Removed several screws holding blower cover. Note blower is located on lower left below the lint screen. Used snap ring pliers to remove snap ring securing old blower wheel(an external snap ring). Removed old blower wheel from motor shaft. Inserted new blower wheel on motor shaft. Replaced snap ring. Replaced blower cover. Replaced thin metal wiring cover. Replaced drum retainer ring. Reconnected door switch wiring. Replaced front panel. Done. A hint on the maytag dryer. If your drum wiggles out too far the belt on the drum might not stay aligned. There is a groove on the drum...the belt should NOT sit in this groove...it should ride on the drum about an inch in front of the groove!!!

I opened the top of the dryer to gain access to the outside of the drum. Then I removed the screws holding the old drum veins in using the electric drill with the nut driver attachment. Then I positioned the new veins in place on the inside of the drum and replaced the screws from the outside of the drum to hold the veins in place. Then I replaced the top and was ready to go.

This is the third repair that I have done using parts from parts select. the other two repairs involved replacing electrical parts. Specifically thermostatic controls or swicthes. I am very happy with the parts and the diagrams provided on your web site without wich I would have had to replace my dryer a long time ago.