Models > DE22CS > Instructions

DE22CS Maytag Dryer - Instructions

All Instructions for the DE22CS
706 - 720 of 797
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer/Dryer would not start
Neither the washer or the dryer of the stacked unit would start. The website suggested that one of the causes could be the thermostat. I ordered a replacement that arrived quickly. Swapping the part only took minutes, and it started just fine.
Parts Used:
Cycling Thermostat - Limit 135/155
  • James from Salt Lake City, UT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
broken tumbler belt
removed front of dryer removed 4 mount screws replaced belt replaced dryer front
Parts Used:
Tumbler and Motor Belt
  • Barry from Port St. Lucie, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
door did not close
easy
Parts Used:
Door Latch Kit
  • law from deep river, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer noisy
I basically just followed the excellent instructions in the PartSelect video; I highly recommend it. Be careful of other sites, I had one site that told me to take off the top of the dryer somehow, which would have been MUCH harder. Be sure to lay down a drop cloth, it is dirty inside these things.
Parts Used:
Tumbler and Motor Belt
  • Michael from Lawrenceville, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Dryer door would not close
Sooooooo easy! Ordered the part on-line and it arrived the very next day! Watched the 'how to' video on-line and the fix was a breeze. Bought my Maytag dryer back in 1989 and this is the only problem it's had. For a repair just under $5.00 plus shipping? I'll take it!
Parts Used:
Door Latch Kit
  • James from Tabernacle, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
grinding on start and through out running then sounds grind after dryer has stop
Followed the video to the tee really easy. But I have been in the dryer before teflon rub guides and belt.Take the front off, then the drum bracket four screws, open the blower wheel cover, remove the locking clip the wheel just slid off then, put it back together everything lined up just fine. then say to your wife listen to the dryer you can't hear! Works great.
Parts Used:
Blower Wheel with Clamp
  • Neal from Hutchinson, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
rollers worn ,rumbling when drum turned
removed front cover and rear access panel took belt off tensioner removed front drum support removed drum replaced two rollers by removing snap rings and put it back together in reverse... The maytag repair man is still lonely
Parts Used:
Drum Support Roller Kit
  • scott from auburn, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Loud squeak coming from rollers
The online video was the extremely helpful in aiding me in the repair. Thank you so much for posting it. Couldn't have done it without it.
Parts Used:
Roller Shaft Drum Support Roller Kit
  • David from Chino, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
noisy and drum wobbling
Installing the Front Glide Kits was straight forward if you watch the video. The guides resolved a part of my problem, but I discovered the Blower Wheel was cracked and out of round. replaced it and poof its fixed!
Parts Used:
Front Glide Kit
  • Jeffery from West Linn, OR
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
New rollers replaced
Followed the guidance on video.
Parts Used:
Drum Roller Shaft Washer Drum Support Roller Kit Retaining Ring
  • David from Helena, MT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door catch broken.
I pried out the old one slightly and grabbed it with pliers. Quite possibly the metal catch dropped into the door section, but no problem. I pushed the new one into place with the side of the pliers. Probably 3 minutes time.
Parts Used:
Door Latch Kit
  • Byron from Los Angeles, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer started making nocking noise
found info describing the nocking noise found parts to fix it watched video on how to do the repair The step by step instructions made the job so easy We saved over 150.00 in doing the job ourselves. thank you I am amazed at how simple this turned ou to be.
Parts Used:
Front Glide Kit
  • Myra from Dillon, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Wrench set
Was this instruction helpful to you?
Thank you for voting!
Belt broke
Following video instructions, replaced the belt. Did it once before so this time it was easier. Two years ago I replaced the plastic fan as it was spinning on moter shaft making a loud noise. (The moulded plastic fan has a flat which slides on the motor shaft. The motor start up torque over time (15 + years)stripped the flat allowing the fan to spin on assembly.) The mistake I made was not replacing the belt when I had the machine apart to replace the fan.
Parts Used:
Tumbler and Motor Belt
  • John from Del Mar, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Rattling Noise
Replaced the Blower Wheel, the Idler Pulley Wheel, the belt and blower seal. Cleaned inside of the unit while I had it apart. Runs very quite. Very easy to do repairs.
Parts Used:
Idler Pulley Wheel Tumbler and Motor Belt Dryer Blower Housing Seal Idler Pulley Shaft Washer Blower Wheel with Clamp Retaining Ring
  • Daniel from Pleasant Hill, IA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Was this instruction helpful to you?
Thank you for voting!
age
son in law..Video was great help...
Parts Used:
Tumbler and Motor Belt Drum Support Roller Kit
  • Steven from Lawrenceville, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the DE22CS
706 - 720 of 797
Back to Top