DE18CS Maytag Dryer - Instructions

My wife had to help me due to a recent back surgery that I had.

1. Disconnet power. Then if you have room, slide dryer away from wall far enough to tilt it slightly back. We had to do this to remove the two lower front panle philips head scres due to my screwdriver length. If you have a stubby, then you don't need to do this. Remove by pulling out on bottom until the two clips at top disengage from dryer top panel.
2. We removed the four 1/4" head sheet metal screws that hold the front tub support panel (with lint screen). Be carefull of wiring. One moisture sensor wire has to be removed from front cover on lower right side near bottom of tub opening. The remaing wires on left side are long enough to leave them attached and "swing" front panel to your left and in my case, lay it back uprite against the washer front.
3. We slid the tub forward enough to lay old belt down so I could see how it was routed around drive. I wanted to verify paperwork that came with new belt. We then set entire tub out of dryer. You might want to take it to another room if you laundry room is cramped.
4. We removed the nut from back of each support roller shaft, I believe it was 3/8 hex. Then reveresed this procedure to install the new roller and shaft. It was easier to assembly rollers before installing as a unit.
5. I removed the old belt and confirmed its length to new belt. I then installed the new belt over drive sheave and tensioner.
6. We then installed the tub and worked belt around it while keeping it on the drive sheave and tensioner pulley. Had to kind of stick my head into tub to start belt unto it.
7. We checked tub front and rear felt seals and I would recomment\d changing these if your dryer is older than 10 years, we did not have then so kept old ones.
8. We replaced the front tub support and installed the four sheet metal screws.
9. We replaced the front cover and installed the two lower philips head screws.
10. Re-connected power and tested operation.

Just pulled out the old filter and inserted the new one. went great and fit good.

It took me a lot longer to plan the repair and decide to do it than to do the actual work, knowing what I know now, and having the parts, it would take less than half an hour. As there are no repair manuals available, it took one of these reports to give me the confidence I needed to proceed.
I first found out how to open the front (only two screews on the underneath part of the front cover) and opened it to hear the noise, (just put the cover to one side while still connected to the door switch),,,,, sprayed some WD40 all over the place and the noise went away temporarily (DO NOT DO THIS as the oil will burn off on top of heater unit and smell and smoke). I replaced the roller that the drum sits on (above the heating unit) to the right of the drum and the belt. You need a special tool that fits into the little holes in the ring retainer, I got it at Lowe's ($20 +/-). It is a Channellock plier that opens when you squeeze, you have to change the points (comes with it).
So, here is the squence: remove the front panel, disconnect the swhitch (it took some pulling), set aside; remove front drum assembly (only four screws looking at you) and it comes right out; the Drum is light and comes right out as well, it just sits in a dry channel. The belt will fall off.... take the retainer ring off the roller with the special tool... remove roller and replace with new washers (one on either side) replace the ring retainer (recommend getting new one) with same tool. If you remove the small panel in the back of the washer it is very eassy to replace the belt.... I did replace it although the old one looked almost new .. instructions and a diagram come with the parts you buy here by the way... which they should say... place belt on drum per instructions (solid side down), put belt inside the chanell on drum (it will climb to the correct position by itself) put on drum front cover to hold drum in place, and then sting belt on pulley from the back of the dryer. (diagram comes with belt otherwise look at it before taking off the drum) Replace front panel (after reconnecting switch) and you are off (if you want to test without the front panel you have to touch the switch wires to each other (use tape) and do not do plugged in...
After much anxiety but not that much work the dryer runs great and is as quiet as new.... I took the parts off before ordering by the way.... the order came within three days... I am happy to have PartSelect.com .. Maytag had not clue this model even existed.... Thanks

There were two screws to remove the front of the dryer. Then 4 screws to remove the front drum support. Remove the drum. Then one nut each on changing the back drum support rollers. Assemble the drum and front support in reverse, and door front, don't forget to put the new drive belt ovre the drum. Then from the rear panel opening, one screw to change the idler assembly. Easy

I removed the front panel (two screws at bottom, then lifted bottom toward me until the top holders slid out). Then I unscrewed the front assembly that holds the dryer drum (four screws), first propping the drum from below so it would stay in place. I removed the blower housing (seven screws) and could see that the blower wheel was loose on the spindle. The 'D' shaped fitting had rounded out. A pair of snap ring pliers made removing the retaining ring and the wheel clamp a cinch and saved a good deal of teeth gnashing. I slid on the new blower wheel and then did everything in reverse. One caution: be sure the drum is pushed firmly up and back when reattaching the front assembly. (It can be done successfully with two hands). I had to re-do this part of the reassembly because the bottom of the drum was rubbing against the blower assembly. Once that was corrected, the dryer ran noiselessly. Thank goodness for PartSelect's diagrams. They're invaluable.

Removed the two lower screws holding front of dryer assembly in place and "unhinged" it and stood it up on floor. Then I unclipped the two wire leads on inside of dryer door assembly and moved assembly completely out of work area. Next I removed the four screws holding the tumbler frame in place and removed that frame from the work area. Now you can access the blower wheel "frame" and remove 5 or 6 hex screws to get that off and out of your way. You DO NOT have to remove the dryer drum and/or drum belt to complete this repair, so save yourself some work and leave it in place!! Once the blower wheel frame is off, use pliers and a flatheaded screwdriver to get the small outer retaining clip off, and then just pliers to get the wheel retaining ring off the wheel shaft. Put on the new blower wheel, use pliers to replace the aforementioned wheel retaining ring, and then the small outer retaining clip...VIOLA! You're finished! Dryer will run like new with a smooth purr instead of that dreaded rumbling sound.

Unplug the dryer. Remove two screws to remove the front drum housing. Remove 4 screws to remove the front drum housing. The front panel and front drum housing do not need to be unwired to work on the blower. Loosen wire harnesses and move panel and housing out of the way. Remove 2 spring clips holding the blower assembly to the motor shaft. Remove blower. Install new blower and re-assemble in the reverse order. The other stories written on the subject were spot on. This repair also made the clothes dry more quickly. I did not realize that long before the ryer made noise, there was a reduction in air flow. A simple vacuum switch to monitor air flow would tell you when there is a problem or that the filter/duct needs to be cleaned.

There are some really good blow-by-blow descriptions on how to go about the repair already listed here. The main thing is to go slowly and take your time. It was really quite logical for a weekend handy man. The best advise was to use a digital camera to record every step of the way as you disassemble the dryer. I referenced the pictures more than once when I was putting all of the wires and pieces back together. Also, I didn't have a pair of snap ring pliers. My neighbor told me how to use two ice picks to poke in the tiny holes and spread the rings...just be careful! Keep a vacuum handy, there will be lots of lint to clean up. The new motor, belt and pulley work great and I pleased with how well the repair went.

I bought a new one and replaced it.

Took longer to open the box that it did to drop the new lint filter into the dryer. Washed a load of clothes and the new dryer filter worked great

Thanks.

R. Bonker

Removed front panel and tumbler, replaced roller axle,
wheel, and front glides. Anybody can do this.

Looked in one of the back removable panels and saw the broken belt. Took the machines front panel off per a You Tube video and saw the repair was simple but too the time to vacuum out a large amount of Lint Debris that had accumulated over the past 34 years all over the inside of the machine which is dangerous.. After cleaning it all up I simply put the new belt on and put everything back together and it all works nicely again!

I UNPLUGGED TH UNIT.Removed the 2 screws holding the front panel in place, disconnected the electrical leads on the panel. These screws are located on each side of the panel 3 in. from the bottom. Removed the 4 screws holding the shroud. Disconnected the ground wire on the shroud & set both aside. Installed the new belt per the diagram & instructions. Turned the tumbler by hand a few times to verify proper installation. Re-installed the shroud & front panel including reconnecting the leads & ground wire. You need to use both hands in a tight space to install the belt on the pulley & guide(a littledificult) The new belt fit perfectly & the instructions were easy to follow & accurate.

We had trouble getting the front of the dryer off; we tried to pry the top off. It works better if you remove the screws at the bottom of the front panel ;) Once we had the front off, we used a 1/4" ratchet wrench to take the front off the fan housing. We took off the compression clamp off easily with a pair of priers. Removing the retainer clip was harder; we ddn't have the right tool. We removed the broken fan. We ordered the part, easy peasy, from this website. Had to buy a $9 tool to put the retainer washer back on. We reassembled the fan housing and put the fron back on. It worked! Total cost: ~$30.00. Actual time (excluding waiting for parts and buying tools): 2 hours.

I removed the front of the dryer and the drum support plate. I drilled out the old rivets and installed the Glides with the enclose rivets. The Glides came loose in a few days! The holes in the glides are larger than in the old Glides. I disassembled the dryer again and reassembled with my rivets. This time I held the rivet gun inside the perimeter of the dryer so that the head of the rivet is opposite the initial installation. So far, so good, except the dryer still squeaks. The idler pulley is now the culprit. White grease burned up. I reassembled with high temperature grease. If that does not work, I will need another idler pulley. The journal looks very worn. the dryer is 30+ years old.