Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
I followed others instructions on this site to disassemble but felt confident since 2-3 years prior I had replaced the felt top/bottom guides around the drum and the drum belt. The video on this page is also helpful
1) Pop the top with a putty knife 2) Unscrew two screws that hold the front onto the dryer frame 3) Lift front from two clips at bottom of dryer 4) Release tension from belt (unscrew/remove rear access plate) 4) Lift drum up and forward out of dryer 5) Unscrew drum bearing 3x screws from inside of drum 5) Remove the drum bearing holder 6) Pre-thread the rear drum bearing!!! Very important. Thread by screwing a supplied screw slowly through the pre-drilled holes. 7) Attach drum bearing 8) Attach new rear holder/cup & ball bearing (ball bearing goes on outside of plastic cup) 9) Use lots of supplied grease, espeiclly helpful that it acts as a temporary glue holding the ball bearing in place 10) Reverse steps to assemble
I'm glad I bought the entire rear bearing kit as I found the bearing holder had completely worn through and partially melted the metal cup. The ball bearing was missing - gone!
Also found that the power cord had partially melted, so I replaced that from the hardware store. Scary.
This was for my Daughter's dryer. A helper really makes this quick and easy. First of all-UNPLUG the unit from the wall. I pried the top up with flat screwdriver. Laid the top back against wall. Removed the two wires from the door cut-off switch. Then removed the two screw attaching the front to the cabinet. Removed the small access panel on back of cabinet. Depressed the belt tensioner to release pressure on the leather drive belt. Went back to front, pushed the belt to the rear of cabinet, then lifted the back of drum to pop the bearing up and out of the plastic cup. I then tilted the drum forward and down and removed through front of cabinet. Reached inside the drum with Phillips screwdriver, removing the two screws to realease the bearing and BB bracket from back of drum. I attached the new bearing cup with BB to the back of cabinet, filling the cup with the high temp grease provided in the cup. Before installing the new bearing on the drum, I ran the new screws into and back out of the new bearing to cut the threads, making it easier to attach on the drum. I then put the drum back into the cabinet popping the bearing into the top of the plastic cup. Next I went to the back, put a bit of grease on the shaft that the tensioner bearing rides on. I re-set the belt on the tensioner, making sure the belt was back in the original position around the drum. I then re-attached the front cabinet centering the front of the drum on the felt. This felt supports the front of the drum. I manually gave the drum a few turns to make sure the drum was centered properly, and belt was mounted correctly. I then re-attached the two wires to the door switch. Slid the dryer into position, inserted the plug back into the outlet. Turmed it on, and now the dryer runs like new again. My Daughter is happy again. You will want to have a vac handy because it is unbelievable how much lint and dust are in the cabinet. I also took the filter bracket apart and cleaned it too.
Taking it apart was no problem other than having to remove solidified grease in order to remove bearing. Also I found it easier to remove belt by removing screws holding drum in place first. Putting it back together was more involved. Taping metal strip to back with scotch tape made putting in new bracket a breeze. Tipping dryer on its' back was the only way I could get the screw holes to line up when installing the drum. Removing the vent cover, and installing from the back, made re-installing the belt tensioner much easier.
first and foremost, watching video on replacement/repair was key to success.furthermore, i ordered part one day and was at my doorstep the following day. the installation process took approximately half of an hour which included vaccuuming cabinet of lint.
We followed the video exactly. The video itself was simple and straight forward. Our model was a bit different than the video's example. The video's example had their spring action for the belt configured differently. When we finally figured out the difference, we were able to finish the job within minutes. The dryer now runs like new. We aren't mechanically inclined. That's why it took us so long. I still would recommend this company to anyone because it saved us time and money. The video really helps!
There are really good instructions with photos on line - search squeeky dryer. I would add that it is easier if you mount the new bearing assembly on the drum before placing the drum back in the dryer cabinet. I guess this is obvious but was not stated in the referenced instructions. The round bearing slotts fairly easily into the plastic pillow block mounted on the back of the cabinet. Just make sure the small ball bearing remains in the center groove - lots of greese will help this.
The part arrived just in the nick of time as my wife and daughter had strung up rope all over the family room to dry clothes. My son helped me lower the dryer to floor level ( this is a stackable washer/dryer set) Removed the top and front of cabinet. Removed the belt and popped out the drum. Took this opportunity to clean the amazing amount of lint from the blower housing and discharge hose ( it is my opinion that the accumulation of lint and the subsequent rise in operating temperature is the main cause of this bearing failure) Removed and replaced the rear bearing and greased it. Reassembled the drum,installed the belt and reassembled the cabinet. the only tools used were a screwdriver and a nut driver....and of course a vacuum cleaner. The rebuild kit is very complete and is the only way to go. Thanks for your fast delivery time, one more clothes line in the family room and I wouldn't be able to watch T.V.
First, used a putty knife to open the top of the dryer. Second, unscrewed the front panel and removed it by pulling up and out. The drum drops down slightly after doing this. Third, open the back grating and disconnect the belt from the motor and idle pulley. Fourth, Pull the drum (with belt) out through the front opening. Jerk up HARD on the back of the drum to disconnect it from the bearing seat. Fifth, replace bearing parts and seat according to diagram. I found it very difficult to unscrew the bearing axle from the drum. Had to hold down the drum and press hard to get screws to turn without stripping. Finally, put back together in reverse, don't forget to put A LOT of grease in your new bearing seat before reconnecting.
Dryer was making LOUD, constant squeal while running
Followed others directions and it went very well. I could not believe how much lint was packed in the bottom of the dryer! Need to clean this area out perhaps once a year.
Bearings Went and Idler Roller fell apart, not allowing drum to turn
unbolted one bolt and replaced old unit with new unit....took only a few minutes. Part was supposed to arrive in 3 days, but arrived next day....thanks very much!
The first part was the most difficult-opening the front of the dryer cabinet! Once open, the new belt was installed and then the new idler pulley was put in-place. The cabinet was closed-job done.