Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Torn ratty old lint filter
Finding parts for very old appliances (that otherwise are working great!) was very much appreciated...lint filters are very very important and this one has served it's useful life. Thank you for such an amazing parts inventory, good prices, and FAST delivery!
I opened the top,by removing the two screws inside the door on the top. then removed the frount by removing the two 5/16 sheet metal screws inside facing the frount. then pulled the drum out and replaced the berring. Cleaned out the lent from the motor and duckings. Then reasembled.
Easy as steps 1 & 2, remove old filter & replace w/ new. It fit perfectly which was my main concern, as I could not tell from picture if the length was correct. I am very pleased w/ product & it works just fine..
Backwards to start- here's the correct way.Disconnect power and vent hose-tip onto front-remove bottom plate allowing access to bottom of dryer and the belt pulleys-remove the small plate in center and under that is a C-clip holding the drum shaft in place-remove the clip and washer-sit dryer upright - open the door and remove the 4 screws under the upper lip which hold the top of the dryer in place-lift up top and secure or have someone hold it up.-inside the top front on both sides are 2 screws per side and there are 2 screws at the bottom under the kick area, remove all 6 of these screws and the front of the dryer will come off-watch the wires-with the front off you can pull the drum forward to allow installing the new belt. - hold the new belt in place with a couple of pieces of tape-reverse the procedure to put drum back together and then thread the new belt onto the drive pulley and under the idler tension pulley.- reinstall back plate, vent hose, power and you're ready to go have a beer.
1. removed old switch 2.wrote model # 3. went to web site found part 4. ordered part 5 part came in 2 days 6. installed part in 15 min. works like new saved over 95.00 thanks ed
My husband and I had taken apart this dryer before, so the second time was a lot easier. The first time we took it apart it took 2-3 frustrating hours. So, if it's your first time, plan for longer.
1. Before we started anything we unplugged the dryer and disconnected the vent. 2. We removed the top and loosened the contol panel on top. 3. We removed the front. Be careful of the wires. You can label them, or just remember where they go. 4. Lay the dryer down on it's back. This make's it easier to remove the drum. 5. Remove the drum, but gently slide the belt off first. Don't stretch the belt removing it. 6. Once the drum was removed, we removed the screws from the inside of the drum. 7. We didn't need to use the entire kit, just the part that sits in the center and spins...kinda looks like a top. (Yes, that's my technical description) 8. We screwed in the new "top" and put the dryer back together.
Really the only part I had to help with (this time)was putting the drum back in to make sure it sat where it was supposed to. It made a big difference that it was laying on it's back...we didn't do that the first time, which was part of our frustration.
Putting the belt back on is a little tricky too. We had instructions still for our dryer to refer to put it back on. If you don't have yours, just google or bing for the instructions. There's website's out there with great pictures.
Removed the top, four screws under the front inside the open door. Then the removed the front, two screws inside at top by drum and two screws on bottom. Then pulled out the drum, from there I was able to get to the bearing that was bad. Mine was a older model than the instructions showed that came with my repair parts but it was colse enough to get the job done. Your website is AWESOME!!! The entire experience was wonderful and made my repair as painless as possible. I have already recomended it to my friends, keep up the great work.
The wire mesh on the lint filter separated from the frame and lint was getting inside the dryer.
Took the old filter out and inserted the new filter which was a near perfect fit on a 36 year old dryed that is still kicking! Delivery of the part was less than 24 hours after ordering over the phone. Thanks1
unknown 25 year old GE dryer started making strange scraping noises when running. This even when there were no items in the appliance. Turning off the gas, and unplugging the power I disassembled the unit to find the nylon drum bushings worn down. Especially the felt like material under them that I think dissipates friction heat. A quick order to GD for the parts, 2 days later I had the part installed, and noise was gone.
Pulled the old filter out of the door of the dryer and then removed the new filter from the shipping box and took the new Lint filter out of the packaging and then slipped the new lint filter into the lint filter holder and started up the dryer and away we went on our happy way. Thanks to all of you guys and gals at PARTS SELECT.