DBB3300GA0WW General Electric Dryer - Instructions

Followed the video on your web site.

It took longer to watch all 3 instruction videos than it took to actually complete the repair. Great instructions for an amateur do-it-yourselfer. Made my wife love me again!

Watched parts select video. Removed door screws. Pulled door off. Removed top screws. Pulled top off. Disconnected wires. Removed light bulb which broke. Removed drum bearing. Used pliers to remove the remaining part of the broken light. Put in new drum bearing. Installed drum bearing slides. Two are recommended. Put the dryer back together. The noise has stopped.

Doesn't get any easier. Lined up the D shape on dryer and timer knob and just popped it in. Working great. I wanted to comment on the super fast shipping. I have never had anything ordered and delivered to my home so fast. It took less than 24 hours to get to my door from the time I ordered it and we chose just the regular ground shipping. Amazing!

I watched the video on PartSelect.com on how to change out the Front Drum Bearing and where and how the Drum Bearing Slides were installed and then I got a Phillips Screw Driver and a pair of Needle Nose Pliers. The first thing I did was unplug the dryer. I unscrewed the two screws located at the top corners of the door opening that fastened the top of the dryer and then removed the top and set it aside. While I had the top off I took the opportunity to note the condition of the Drum Belt in case it also needed to be replaced. The drum belt appeared to be in good shape so I removed the two screws that fastened the front of the dryer, pulled the front of the dryer forward letting the drum fall slightly off of the Front Drum Bearing, and then disconnecting the door switch wires making sure I wrote down where each of the three wires attached to the wire harness on the front panel of the dryer went. I pulled the front panel off and the first thing I noticed was that all four of the Drum Bearing Slides were GONE as were the brackets on the Front Drum Bearing that held them. There were a couple piles of grey dust on the front panel which were the remains of a couple of the Drum Bearing Slides. I unscrewed the light bulb and just pulled the Front Drum Bearing off and discarded it. The new Front Drum Bearing snapped easily into place and I installed the Drum Bearing Slides, of which there are TWO types, into their proper brackets. I cleaned out the lint from the exhaust vent on the bottom of the front panel as well as the hardened lint from around the fan on the bottom of the dryer where the exhaust vent on the front panel attached before I plugged the three door switch wires back in their proper locations on the front panel wire harness and, making sure the drum rested on the Front Drum Bearing, reattached the front panel and screwed the fastening screws back into place. Then I reattached the top, which took a few minutes and some colorful metaphors because anyone who has ever done any kind of repair knows that the mechanism you are trying to repair never wants to go back together. After getting the dryer top where it was supposed to go I screwed the fastening screws back into place. Before I plugged the dryer in to test it I took the opportunity to remove and completely clean out the dryer exhaust vent pipe from inside the pipe that comes out of the dryer all the way to where the vent exhausts to the outside. You wouldn't believe how much lint hardens on the insides of the exhaust vent pipe. I reattached everything, plugged in the dryer, and turned it on. The dryer was as quiet as it was when I first bought it.

took out old one and replaced it with the new one,took seconds

I went online and ordered the part number WE1M654 and it came within 2 days and just pulled the old knob off and inserted the new knob and it worked.

took the knob out of the bag and snapped it into place...all done!!!

The repair was performed in the laundry room which was large enough the handle all the parts when disassembled. I followed the video and it was perfect without any errors. The job was simple and even putting on the new belt without having the ability to see what I was doing. You'll understand when you view the video and perform the job. Just follow the instructions including using the newly supplied screw to tap the new holes.

Took new knob out of bag,slid new knob on. Worked great

went on this web site order parts and got instruction, tis was the BEST website

It was no big deal I just replaced the used parts with the new ones. I just needed help knowing were the white and black bearings went.I went to the web site and got the information I needed. I didnt think I would be able to find parts for a machine as old as ours. Saved us big bucks.

follow the video, and in no time fix and ran smooth, like brand new, love this website, fast and reliable

I watch the videos, your company told me to go to on the internet when I received the parts. I could not believe how easy it was to change the parts' The videos make the job as easy as the video showed it to be. Your videos and parts are the best. Thank You Greg

This is the 2nd time I replaced the drum bearing in the past 2 years on my 16 year old GE dryer. I found the parts needed by the diagram and followed the how to video which was very helpful and easy to follow. My parts came in 3 days and I hope to get another few years out of my dryer.