Models > DBB3300GA0WW > Instructions

DBB3300GA0WW General Electric Dryer - Instructions

All installation instructions for DBB3300GA0WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the DBB3300GA0WW
1-15 of 690
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was squeeling when running.

  • Customer: Daniel from Chicago IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 389 of 391 people found this instruction helpful
I removed the two screws at the front above the drum opening (with the dryer door open). The top panel then lifts off. I removed the screw at each side that holds the front panel to the side panels, tilted the front panel forward, which disengages the front of the drum from the front drum glide bearing. I then lifted the front panel slightly, unhooking the bottom of the panel from the dryer base, and swung the front panel aside. I removed the existing top drum bearing guide, which was disintegrated, and snapped in the new bearing guide, with the nylon slide strips installed in the bearing guide. Next pulled out the old felt strip, and pressed the new one in place. I then put the bottom of the front panel back into the bottom of the dryer front, and while lifting the drum to asure it fit over the bearing guide, pushed the front panel back to a vertical position to mate with the side panels. I then replaced the side panel screws, replaced the top, and replaced the front top panel screws.

Intermittant squeaking noise

  • Customer: Mark from Addison IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 402 of 475 people found this instruction helpful
Basically, I followed the same steps a prior person posted.
1.Removed the two screws inside the door, on the top part of the opening.
2.Lifted up and removed the top.
3.Removed two screws holding the front panel in place.
4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at the drum bearing without pulling the wires connecting it to the front panel. The wires are not very long, so I had to be careful not to pull on them.
5.Carefully pried off the old drum bearing, using just my hands. It was fairly tight, and popped out just as I started to worry if I was putting too much pressure on it.
6.Checked to see how the old felt was installed, then I pulled out the old felt.
7.Inserted the new felt, being careful to insert one end into a slot the same way the original was installed.
8.Inserted the new slides into the new drum bearing. The gray slides went in at the eleven and one o'clock positions, the white slides went in at ten and two o'clock.
9.Removed a surplus plastic piece from the new drum bearing (where the light comes through).
10.Inserted the new drum bearing, putting the bottom tabs in first, then pivoting it into place. I squeezed it into place to make sure it was tight.
11.Lifted up the drum and put the front panel back on.
12.Screwed the front panel back on, using the two screws.
13.Carefully put the top back on.
14.Screwed in the two screws inside the front door to fasten down the top.
That was it! I started up the dryer and it worked fine. No more squeaking.
About the only thing odd about the repair is why PartSelect sells each slide separately (i.e., I had to order 2 white slides and 2 gray slides). I can't imagine replacing just one, so why not package them in pairs, or maybe even all four in one package.
At any rate, the repair was easy, and a lot cheaper than having someone come out to fix it.

Timer knob cracked and would not turn on the dryer

  • Customer: Kathleen from Greenwood IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 140 of 205 people found this instruction helpful
Very easy. I just snapped the new timer knob on and I was ready to go.

Dryer made LOUD screaching constant sound

  • Customer: Brian from Langhorne PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 132 of 197 people found this instruction helpful
(1) open dryer door (2) remove screws holding door on and put door aside. Probably doesn't have to be done but I think its easier and safer so you don't accidently bend the hinges. (3) remove 2 screws holding top onto front. of dryer located in recess that door sits in (3) pull up on top and remove (from slots by the control panel) (4) remove final 2 screws holding front onto frame of dryer. You can disconnect the connectors from the front panel back to the dryer to make the job easier or work with it without disconnecting. I'd take your time and clean any lint dust, etc. (5) the Drum Bearing removes fairly easy as it is just snapped into 2 slots. insert slids into slots.... make sure you order all 4. Mine were all beat!. (6) replace with new Drum Bearing. (7) I did the lower felt seal as well. Pay attention to how you took the old one off and replace the same way. Remember it stretches to fit into the slots. Put all back together. Remember to front panel has to sit correctly into bottom slots before you screw the top screws back in. All in all.... a simple project, and no more noise!!!!! Great to have websites like this. Easy ordering, quick shipping, great diagrams.

original duct was broken

  • Customer: Chad from Gilbert SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 83 of 89 people found this instruction helpful
Dear PartSelect.com,

My repair went off without a hitch.

2 screws removed to remove top.
4 screws removed from inside to remove front panel w/ door.
4 screws removed from top of control panel, loosed and popped top right off.
Flathead screwdriver to pop off old plastic panel.
Removed old wire chase (plastic, approx 3” long).
Removed built-up lint, wiped down area for new duct.
Snapped new duct on.
Dryer works like new!!
Took about 35 minutes, most of time spent cleaning up inside of dryer from lint due to broken duct.

One problem was that salesperson sold me on a new felt strip to go with new duct. That felt comes already installed on the new duct so I did not need it. Cost me a few extra dollars I did not need to spend.

Other than that, easy ordering, fast shipment, and parts are as close to original as possible.

Thanks for all your help!

Drum belt broke

  • Customer: Adrian from Middletown MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 77 of 100 people found this instruction helpful
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on.
This was a first attempt ever at fixing an appliance and it was no big deal.

Broken Knob Post

  • Customer: Jaren from Lemoore CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 60 of 73 people found this instruction helpful
First I unplugged the dryer, then I removed the access panel on the back of the control panel. I removed the wires from the back of the switch...Here is where I messed up. I removed the switch prior to ordering the part, the bad part is the way I removed the part. When you get the new part in you will be able to see how it will be mounted to the control panel. I had no idea, so I did what was necessary to remove it. Needless to say, I bent the hell out of the hole that the switch mounts in. In turn, the installation of the new switch did not go as easily as I would have liked. After straightening out some metal and drowning the thing in epoxy, the new switch is installed. I hooked the wires back up on the back of the switch, plug in the dryer, and dry some clothes. Standing victorious over the dryer with beer in hand, not only did I accomplish the mission but I learned my lesson... destructive removal = BAD!

The dryer drum turned ok, but the gas heat did not start.

  • Customer: Gary L. from Freeport IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 46 of 62 people found this instruction helpful
First I found and watched three videos on how to open the dryer and replace the igniter.
Then I opened the dryer, but I did not remove the belt as suggested in the video, and then I removed the ignitor and flame detecter as the videos had shown.
I got on-line and ordered the new parts from PartsSelect in the afternoon and had them in my hands the next morning by 9:30 am.
I installed the new parts and everything worked fine again. You must be very careful with the igniter to not touch it with hands or anything else. I practiced puting in the old parts first.

The dryer door handle broke off.

  • Customer: Jim from North Richland Hills TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 35 of 38 people found this instruction helpful
I pried out the remaining pieces of the handle out of the door with a screwdriver. When the new part arrived, I snapped it into place and it was done. It fit perfectly.

Dryer would heat initially, but would not heat throughout entire cycle.

  • Customer: Erik from Newport ME
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 32 of 37 people found this instruction helpful
-Removed top panel
-Removed right side panel
-Gas coils were held in together under a metal strap
-Removed 2 screws holding strap
-Unplugged 1 wire harness to each coil
-Removed Primary and Holding coil
-Replace with two new coils, replace strap and plug in each harness
-Replace side, then top panel
-Under 1 hour job...Took 45 minutes to remove/replace panels and only 5 minutes to replace coils.
-Anyone with a little mechanical ability can save $150 in labor and spend just $50 in parts to fix this problem.
-Questions: Erik at elstransport13@gmail.com

squeaky dryer for a week or two

  • Customer: warren from Flint MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 29 of 32 people found this instruction helpful
First I unplugged the dryer and turned off the gas

Second I opened the door and unscrewed the two screws that go up into the top panel and hold it in place (you will need to get down and look under the top of the door jam to see the screws).

Third I lifted the front of the top enough to remove the two screws holding the front panel on (Use a magnetic screwdriver if you have one you do not want to lose the screws taking them out or putting them back in)

Fourth positioned a chair to lean front panel against so it would not fall over or strain the electrical wires that run to the switch in the door (slide the front panel off slowly supporting the drum with your hand so it doe not drop hard on the motor wires or burners)

Sixth determined the parts I needed and ordered parts from pars select and got them in two days

Seventh when new parts arrived I unclipped the old DRUM BEARING removed the felt gasket, put the felt in the new Drum bearing and clipped it in place

Eighth clipped in the 2 new Dryer Drum Slides and 2new SLIDE WH slides

Ninth Vacuumed out dryer and vent pipe completely

Tenth reassembled dryer being careful to make sure drum was properly aligned as I put the front panel in place and the belt was in the proper place on drum and all the screws were back in place.

Ninth turned gas back on and plugged in dryer

Ten turned on dryer to test squeak was gone

Hints as soon as you hear a squeak look into it and you will probably not have to replace the DRUM BEARING. But if any of the Slides are bad replace them all. Check your belt and felt gaskets to see if they are in good shape. If everything up front is in good shape and it is not the motor squeaking it could be the back drum bearing. Take your time keep your old dryer running for a few more years and save the $40 dollar service call. Do not forget to clean out all the old lint and dust out of your dryer and vent pipes not only will you reduce the risk of fire you will be allowing air to pass through the dryer more easily drying your clothes in shorter time.

belt broken, pulley worn out

  • Customer: Anthony from Mpls MN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 27 of 32 people found this instruction helpful
Removed 4 screws from top of control panel , remove 2 from back to lossen top of dryer. Removed rear lower access cover,6 screws on back of dryer exposing pulley and tensioner, remove broken belt and vaccuumed out a ton of lint , removed pulley and tensioner and replaced. From the front remove 4 screws and take off front of dryer, disconnecting several wires, again vaccumed out lint, lifter drum evough to replace belt. Reassembled

Gas dryer was not getting hot and smelled like gas inside drum

  • Customer: Todd from Santa Rosa Valley CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 31 of 44 people found this instruction helpful
Removed lower front panel and then front including door (need to remove the top to access screws.) Replaced both the ingiter and heat detector. The tricky part was getting access to the long tunnel-like bracket that houses the igniter. Washer and Dryer are in a tight cutout space in very small laundry room.

DRYER WAS MAKING A LOT OF NOISE WHILE RUNNING

  • Customer: Tracy from Winston Salem NC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 24 of 25 people found this instruction helpful
I ordered parts based off other peoples findings. I took the top and front off the Dryer. I found the drum bearing(really only a plastic bracket. The slide were completely worn and the drum was wearing into the plastic drum bearing. I popped the old drum bearing out and put the new on in. There are actually 2 sets of slides (4 total). I only bought 2. I reused two of the existing slides. I put the unit back together and it was a lot quieter. I need to order more of the slides. They are only a couple dollars a piece and take most of the beating. I should've but didn't get the pasking or gasket. it was broken. I think it'll be fine though.

dryer would not get hot after igniter went on, no gas being let in.

  • Customer: Vinny from Port Chester NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 23 of 29 people found this instruction helpful
Removed top cover of dryer with screwdiver 2 screws, removed front cover 2 small bolts with 5/16 scoket. Removed coil brackets with shor screwdriver replace coils as ness. and put covers back on and works great!

Vinny
All Instructions for the DBB3300GA0WW
1-15 of 690