Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CWG3600AAS > Instructions

CWG3600AAS Maytag Wall Oven - Instructions

All installation instructions for CWG3600AAS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the wall oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CWG3600AAS
76-90 of 176
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven wasn't getting hot and smelled gassy

  • Customer: patricia from tinton falls, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
We took the interior floor out, pulled the stove away from counter, before that turned all electricity to the house off. Then we unscrewed the ignitor inside then underneath unplugged it and plugged in the new one, cleaned to oven and screwed the ignitor in and replaced the interior floor and we were done.

Oven would not light

  • Customer: David from Kingston, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 1 people found this instruction helpful
First I tried oven ignitor. Did not cure the problem. Then ordered short sensor and it cured the problem. Pull range out & unplug unit.From inside unit remove two screws holding short sensor in &pull out from inside. Unhook sensor. Slide in new sensor& secure with two screws. Had to remove two screws on back of oven to plug in sensor to existing plug. Very simple job.

Oven Gas Valve And Glow-Bar Burn Out

  • Customer: Robert from Georgiana, AL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench set
  • 0 of 1 people found this instruction helpful
The repairs was easy,once I found the problem I turned the gas off and unplug the power supply cord. For the oven gas valve I used a 5/8 wrench to take the gas supply line away from the side of the valve inside the over. I used a 1/4 nutdriver to remove the two screw holding the braket down over the valve. For the glow-bar I donnected the power supply plug and used a 1/4 nutdriver to remove two screw holding it in place next to the brun.

Oven would turn on but not heat up

  • Customer: Sheina from New York, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
We ordered the replacement igniter and basically was very easy to replace. We ended up spending $50 for the part as opposed to spending $261.00 that Sears was going to charge.

you couldn't use the oven because the gas igniter quit working

  • Customer: James from Coosada, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
I was sure my problem was due to a gas ingiter that was no longer working. I read about others that had the same problem as I did. I ordered the part from Partselect because they had a 30 day no hassle parts return policy.
I removed the oven racks and 4 screws to get to the igniter.
I unpluged the igniter, put the new one in, and replaced the racks. Very simple and easy to do.

Gas oven igniter glowed but didn't lite

  • Customer: crystal from Stonington, ME
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
I removed the cover protecting the igniter. I pulled the stove away from the wall to get at the connect for the igniter. I loosened the 2 screws which held the igniter.
Took the new igniter ran the wire to the back to the connection and mounted the igniter with the 2 screws. Turned on the oven to make sure it works and it did. Turned off the oven, replace the cover and pushed the stove back in place. No big Deal!
Your web site was very helpful. Thank you so much!

Wrong connector on new part.

  • Customer: Michael from Corona, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
seamed easy enough. Found the part and it looked identical, However I could not see the connector in the picture because the logo covered that part of the picture. Had to cut the connector off the old igniter and crimp it on to the new ingniter.

Oven Would Not Light

  • Customer: EUGENE from ELKHORN, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Changed the igniter

Oven would not light

  • Customer: Mark from Glencoe, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Replaced gas oven ignitor

Smell of gas and would not always light or took forever to preheat

  • Customer: William from Forked River, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
Remove the oven door by opening halfway and lifting door away from stove. Removed racks and bottom pan from oven area exposing the gas bar and vertical mount igniter. Next remove bottom storage door. With phillips screwdriver remove 2 screws securing rear cover plate in back of storage area, accessing the igniter connection, and unplug the plug. Next back in oven, remove 2 5/16 sheet metal screws securing igniter with a nut driver and remove igniter by getly pulling disconnected end thru to oven. Now reverse process, install new vertical mount igniter and push connection down thru to storage area, then reconnect wire connection and put cover plate back on.
At this piont I turned oven on and checked igniter, it glowed red right away and the oven lit right up. Put storage door, oven door, bottom oven panel, and racks back in and done. Took 15 minutes tops, and anyone can do this, super easy. My oven would sometimes take half hour to preheat to 350,if it even lit, now 5 minutes, and it lights every time. Save the cost of a repair man folks, this one can be done by any weekend warrior.
I would just like to note....if you are uncomfortable with disconnecting wire plugs and plugging them back in, just unplug the oven from the wall as well before changing out the part, just to be safe.

The oven would not come on.

  • Customer: ROBYN from ELIZABETH, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench (Adjustable)
  • 0 of 1 people found this instruction helpful
We hired the neighborhood handy man, and he was able to repair the oven in about 15 minutes. I order the part and received it the next day. Excellent Service!!

Long delay before ignition slow preheat

  • Customer: michael from rochester, NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
Remove oven floor and bottom drawer
remove 2 1/4-inch screws holding ignitor
remove cover plate behind drawer to access P/J
Disconnect plug remove ignitor and reassemble

Did not have gas smell, but ignition took 6 minutes

The oven would take up to 30 min to ignite once turned on

  • Customer: Dee from Prescott, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Once I got the new Igniter, I unplugged the old igniter and took two bolts out. Then remounted the new igniter and plugged it in. Works like a charm!!

would not light

  • Customer: John from Montague, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
Removed the old igniter, followed the wires. Reversed the process and put it back together. Saved big bucks! Thanks for the quick service.

Gas Oven Would Not Light

  • Customer: William from Arlington, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
First I unplugged the range, turned off the gas to the oven and disconnected the gas line from the oven. I pulled the oven out to gain access to the rear of the unit and unplugged the old igniter. Next, I removed the oven door, removed two screws to the floor of the oven and removed it. I then removed the metal covering above the gas component allowing full access to the igniter. I removed two screws from the igniter and removed it. I positioned the new igniter and replaced the two screws. I replaced the covering over the gas component, replaced the oven floor and put the oven door back on. I went to the rear of the unit and plugged in the new igniter. I then reconnected the gas line to the oven range and checked for leaks, No leaks were found and I pushed the oven unit back into place. I pushed the Bake button and the igniter started igniting the oven.

Job completed.
All Instructions for the CWG3600AAS
76-90 of 176