Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
during wash cycle, water poured out of bottom of washer
first we looked at schematics on your web site to see what we thought was wrong and if we felt we could do ourselves. It appeared to be seals and gaskets, so we went for it and carefully took the washer apart. We ordered the parts, cleaned the parts we had such as the tub, and were all ready to put back together when the parts arrived. Again, using your pictures, we reasselbled and when we tested, it worked better than it had been in a long time. And we saved a large repair bill!
Vey Easy to Fix. 1)Turn Water off at the wall. 2)Remove access panel on back of washer. 3) Remove Water pump. It is bolted down to the bottom of the washer by three nut head bolts. when loose the pump can be manipulated and tilted so the belt will have slack and most likely fall right off. Have a bucket ready. Remove water hose from top of pump by sgueaing clam with pliars and sliding clamp up hose. allow to drain in bucket. Lift drain hose out from wall and allow to drain through the pump into bucket. remove hose from pump that goet to drain. Replace pump and reverse steps listed above.
First push inner tub to left rear, all the way, and unscrew hinge from inside of tub. repeat same on right side. lift cover off and unscrew other half of hinge off cover, both sides.reverse procedures and your done. Note: always replace both hinge's new while you have it apart.
Lid switch had deteriated over time and no longer made contact
removed the screw holding the actuator, ordered the new part and replaced it when it arrived. Shipping was really fast and I even received it one day early.
Diagnosed that the snubber had failed. Removed the belt, cam assembly and pulley assembly. Using Maytag brake removal tool #12002012 I removed the brake stator. I removed the front of the washing machine and the rear access plate. I removed the six tension springs. I moved the machine basket and shaft assembly toward the top of the machine. I removed the old snubber and replaced with a new one. I installed 6 new tension springs and reassembled. The washing machine runs great.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
9 of 9 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Severly off balance during spin cycle
My washing machine was severely off balance during the spin cycle. It would bang violently against the side and “walk” across the laundry room. I was able to fix this for under $25 dollars of parts from partselect.com and a few hours. I rated the task as easy, but I am somewhat mechanically inclined. Others may find it a bit difficult but I believe anyone except an absolute beginner can do this job.
Fix this problem before significant damage is done to your base! Otherwise the job will take more time and be a LOT more expensive. My base had experienced a little damage but thankfully it did not require replacement. When the snubber wears out, it allows the tub to rub against the base. Metal on metal is never a good thing.
Also I chose to replace the springs, even though it may not have been 100% necessary. You have to take them off anyway and they are inexpensive. It is easy to know when a spring is broken, but not as easy to know when it has lost some of its spring. Just makes sense to me to replace them.
I used the directions below which I found on the internet. They are listed below unedited by me. I have added a few of my own comments below that.
• Remove power and all hoses • Lift top by inserting putty knife just inside front clips to release • Remove front and rear panels, 10mm • Disconnect drain hose from bottom of drum, pliers - spring clip • Remove 6 springs from bottom of drum using channel lock or spring tool • Lay on side, remove drive belt by turning large drive pulley and side tension to belt • Remove water level hose on side of drum, pliers - spring clip • Remove drum from cabinet by sliding out top. It is not necessary to remove drum from transmission. • Inspect base plate for damage • Lay drum on padded surface, upside down • Remove C clip, drive pulley, being careful to observe order of parts and washers • Loosen 6 screws holding down old snubber. DO NOT REMOVE SCREWS, THERE IS A VERY STRONG SPRING UNDER THIS PLATE. Loosen screws only enough to get old snubber out. • Clean dust from area. • Insert new snubber, keeping it even while tightening screws. • Reverse other processes above to assemble washer. Replace any broken drum springs. Replace belt if worn.
My tips:
• After you remove the tub you will see a lot of fine white dust in the bottom of the washer. That is from your old worn out snubber. Vaccum it out.
• I didn’t have a spring tool but I found that using a pair of vice grips to remove and replace the springs was easier than using channel locks.
• Technically, I believe the clip is actually called an e-clip. If you have the correct tool for this removing and replacing it will be a lot easier. I did not have the tool. I used an open end wrench that was just the right size to butt up against the two ends of the clip. A light tap with a hammer against the other end of the wrench and it popped right off. I used a pair of needle nose pliers to put it back on.
• Also regarding putting the e-clip back on, at first I could not see the groove that the clip was supposed to slid into. It was below the little plastic piece with the teeth. I used a small flat screw driver inserted into the groove to gently pry it up and had someone gently tap on the plastic piece which pushed it down enough to expose the grove.
• I highly recommend heeding the warning regarding the loosening of the 6 screws holding the snubber. I did not have any trouble with this but there is a 200 lbs spring underneath that you do not want to release. It could injure you and might be hard to put back. Just loosen each screw 1/4 turn at a time until the snubber can be removed.
tip washer up on wooden blocks.remove drive belt.remove "E" clip from tub drive pulley and remove all the parts.Install new parts in kit as per instructions.machine works great!
One of the two bolts that holds the motor in place broke off and since the bolts are actually embedded in the motor I had to buy the whole motor rather then just a 25 cent bolt.
First I took the front shield off, then I took the motor off.
After pulling the machine away from the wall and turning off the water and unpluging. I simply removed the panel in the back and reached underneath and removed the belt. Took off the hose clamps and removed the three screws holding the pump on. Put the new pump back in place and hooked up the hoses. Then put the belt on for a test run.......all OK put the back on and was done. Whole job about twenty minutes. Saved over two hundred dollars doing this myself. Very simple repair.
Washer made a loud noise during spin-eventually stopped spinning
I was able to get the belt off easily but the belt was fine. I changed the snubber easily also. But that wasn't the problem. I went through all the parts that are easy enough to change without a mechanic but turned out it was something inside the innerbasket and we had to junk the washer and it was only 4 yrs old.
just took the front off and then took the old motor off and switched over about 2 parts from the old to the new and then put the new part on and then placed the front back on and it was ready to go
First I removed the bolt and removed the old agitator and post assembly then I put the new agitator and post assembly in place and tightened the bolt. It was so easy, when I called the manufacturer they wanted to send out a technician, but thanks to Parts Select I fixed the problem without spending alot of money and without the hassle.