CVG4380PK Jenn-Air Cooktop - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replaced filter
-
ELOISE from MILFORD, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
482 of 504 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old grease filter that I actually did not know I had to change
Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen
Parts Used:
-
deborah from fort pierce, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
448 of 534 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My Jenn-Air is an "antique." The filter was disgusting!
I had put up with a filter that got more and more raggedy every year, but I thought my 30 yr. old range/grill top was too old for me to find an replacement filter. What a great service you offer. I found you by web-surfing, typed in the model #, and presto--you sent me the shiny new filter. All I had to do was pop it in and throw away the nasty grill (after washing the scent off to keep the bears out of my Colorado garbage.) Thank you!
Parts Used:
-
marion from aspen, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
166 of 319 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Falling apart 20 year old grease filter for downdraft counter rangetop
Cleaned out the downdraft cove, inserted the new filter, and put old filter in garbage can. Laughing. Thanks. Wish you had a FAQ's hotline. I'd like to know if the radiant inserts fit the older coil-type models.
Parts Used:
-
Roe from Raleigh, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
147 of 289 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
top burners on stove won't ignite ,no clicking noise
remove small panel on right side of stove,then un clip moduke and put wires from old module to new one.
Exact fit nomproblems.
Exact fit nomproblems.
Parts Used:
-
scott from centreville, VA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
47 of 71 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas range would not light
Replaced spark module but same problem persisted. Realized that the insulation on the spark ignitors were all cracked, causing a short.
Lesson learned: check the condition of the spark ignitors first as these have a tendency to crack. Even the smallest crack will cause a short.
Ordered new spark ignitors and plan to complete repair.
Lesson learned: check the condition of the spark ignitors first as these have a tendency to crack. Even the smallest crack will cause a short.
Ordered new spark ignitors and plan to complete repair.
Parts Used:
-
Mike from Menlo Park, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
16 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One part of the grill burner came detached, caused fire at the connection
I turned off the burner and allowed it to cool. I then checked the website for the part and also got a new grease filter and grill grate. When the parts came, I plugged in the new grill burner, replaced the grill grates, and dropped the filter in place. Total time was about 8 or 10 minutes--most of which was opening the packages. The grill burner is designed so that it can be removed and replaced with a standard 2 burner unit. No tools were needed. I was glad to find the parts for my 17 year old dual-fuel range.
Parts Used:
-
Anaclare from Oak Park, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
10 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Simply needed a new knob, however...
However, I was very happily surprised how fast I got the part even though I did not specify fast shipping.
Parts Used:
-
Shane from Dallas, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
20 year old burners were slow to light and hard to adjust for our propane fired stove. And, they were scratched and ugly
Removed four screws; withdrew two burners; set two new burners in place; installed same old screws. That was it. When I turned them on to adjust the flame, they came on almost instantly and no adjustment was needed.
Wife loves the nice new look.
Wife loves the nice new look.
Parts Used:
-
thomas from Goodrich, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Part arrived broken.
Contacted customer service via email. Included a description of the problem as well as a photo that clearly showed that the Front Burner Assembly was, in fact, NOT an assembly when it arrived.
Nobody even acknowledged my email.
This was a $140 assembly.
Never again will use these guys for repair parts.
Nobody even acknowledged my email.
This was a $140 assembly.
Never again will use these guys for repair parts.
Parts Used:
-
Thomas from HOLLISTON, MA
-
Difficulty Level:Very Difficult
-
Total Repair Time:30 - 60 mins
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Downdraft Motor Bearings Shot
I first had to purchase the replacement motor which was quoted from a high of $236 to a low at graingers of$100. 00. The counterman at graingers removed the blower fan from the motor for me with a special long handled allen key. I then degreased and cleaned the blower fan. I had to cut off the screws on the motor and replace the 3 motor isolators and the urethane foam around the motor. I had to thread the 3 wires from the new motor through the bx cable from the old motor and reattach the fan to the motor. Anyone wanting more detailed informatioin may contact me at:mablume@optonline. Net
Parts Used:
-
MICHAEL from LAKE GROVE, NY
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Reusable Grease filter was old and worn out.
The Model number could no longer be read clearly on the stove electric grill with a down draft vent system, so all I had was the size and looks of the old grease/air filter. I was very happy to come across Parts Select by way of an amazon.com search. Their web site's design and the parts pictures with detailed descriptions made it easy to find exactly what I needed. The grease filter fit perfectly in no time. I have successfully used my cooking grill again.
Parts Used:
-
Gloria from Galveston, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
high blower vibration
blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.
Parts Used:
-
Lawrence from Chandler, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
9 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No spark at top burners
Shut off gas supply
Pulled stove away from wall removed spark ignigtor box .
Installed new one .
No problem.
Good for another 10 years
Pulled stove away from wall removed spark ignigtor box .
Installed new one .
No problem.
Good for another 10 years
Parts Used:
-
Joseph from East Freetown, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
7 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace blower motor
disassemble housing and remove fan and motor. Reatach fan to new motor, connect wiring, place gasket around motor and reassemble.
Parts Used:
-
Richard from Harrisburg, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!