CSX22GRBEAA Hotpoint Refrigerator - Instructions

Followed the u tube video that was on the Part select website. Very easy install when following the video.

Removed frame, unscrewed the electrical panel, and popped the flapper off. Installed new flapper. Replaced the electrical panel and re-installed the frame.

Removed the ice maker control panel and accessed the flapper door, easy switch out for new door and seal. The 2 year old warped seal didn't close and so ice crystals formed in the freezer - new unwarped part and Ta-Da no more problems :)

there was rust inbedded in the ice cube. replaced the front plate in the ice maker bin. If you can't remember what parts you remover, take pictures of the replacement

1. Turn water supply off at wall. Unpulg referigerator. Remove all cardboard backing covering valve. Vaccum under ref. Unscrew water line where it attaches to valve on ref. (Reuse this later) unplug 4 electrical prongs. Mark with colored pen if not already color coded, so can put back correctly. Pull old ice maker and ref water supply out of valve if it does not screw in with nut. Cut very short peice off end of ref water lines. Slide new locks on water supply lines and push into water valve very hard to lock. Cant get them wrong as they are different sizes. Plug in electrical connectors same as you unpluged them. Connect water line to valve from wall. Turn water on and check for leaks. If none. Replace all screws on backing. Recheck for water on floor. If none congrads, just saved yourself about $120. 00 Labor. Take 2 asprin, drink a six pack and go to bed.

I had to defrost large chunks of ice from the rear of the freezer compartment and tried reactivating the ice maker several times before deciding to order the replacement fill tube grommet and clamp. This was very stressful and complicated to accomplish while trying to avoid food spoilage, and consumed a lot of time. It involved removing the ice maker and various panels, plus disconnection of 2 electrical plugs, then using a hair dryer to melt ice build up. The installation of the new parts was quick and simple once they arrived in the mail, and this appears to have solved the leak problem. The fill tube slides easily into the grommet and the clamp, tightened with a screw driver, secures the water feed line on the other end. Fill tube must be carefully threaded through rear panels and into the ice maker receptacle and the grommet needs to be pushed hard and wiggled in order to seat properly in the rear surface of the refrigerator.

Popped off the front frame and front of mother board. unscrewed the assembly to be able to lift up to get to flapper. Lifted it up out of the the way ( wires are attached so it may take one other person to hold it up out of the way). Pop out the old flapper and replace with new one. Easy !

Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.

Did the repair jut like the instructions on the web site stated. There was a good video for doing this repair. Looked at it a couple of times and did the repair right off the bat. Thanks folks.

Reviewed video which was very helpful. Loosened two philips head screws, lifted up ice maker, unpluged power suppy and reinstalled. One of the easiest replacements ever!!

I found you web sight. Determined I needed the hinge assembly. Followed the instructions in the video on your web sight, and it was all better.

easy pry out, disconnect wiring, connect on new switch and press in switch.

Pretty easy other than the tight space to work with..... I was replacing a single heater with a duel, so the space is a little weird to work with but it will fit. Just followed the video that was with the part :) thanks parts select , u guys saved me a lot of money

on the refrigerator side remove two screws from hinge on top of door, pick doorup to remove from bottom hinge using a 5/16 socket remove the two screws holding hinge in place, replace with new hinge. on the door loosen up the screws, no need to remove. the screw closest to the hing axis remove completely remove the old cam, insert new cam lined up with axis of hinge reinsert screw, place door back on hinge and replace hinge on top. the freezer side has water an ice in the door.at the bottom [grill has been removed] of the door a plastic tubing has to be disconnected [make sure water is off] the disconnect is near the door, the coupling is only finger tight. uncou[ple plastic coupling and pull out of connection, pull the nut and ferule off the tubing. now take top hinge off, remove door straight up while feeding plastic tubing thru hinge. the hinge is replaced the same way as the other side. when new hinge an cam are in place, lift door up now feed the plastic tubing thru the hinge till door is in place, replace top hinge. when you reconnect the plastic tubing it helps if you place a lubricant on the end so that you slide the nut and ferule on. the connection should only be finger tight, no wrenches

I took out old part and I put new one.