Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
would not defrost
First I removed the light cover, one screw. Then I removed the rear coil cover, three Phillips screws and two hex head screws. I then defrosted the coils and removed the old defrost element and wiring harness, two hex head screws held in the element, wiring harness just unplugs. I the installed the new defrost coils ( new one had two coils but had a previously designed area for the second element ) and ran the wiring harness up to where the plug was. I then reinstalled the coil cover plate, and light guard and started the refridgerator. Frige runs like new. Thank you PartSelect for the extremely propmt delivery and the correct part. part
removed freezer racks and back panel. removed and relaced defrosting harness. reassembled compartment PartSelect rocks! easy to locate needed parts. price is fair and quick shipping. saved me $$$$
Refrigerator Gasket had split and causing excess sweating inside of refrigerator whick was cauing water to drain out the front door damaging the floor.
Very simple fix. I loosened all screws with a nutdriver, removed old seal by pulling it out from under the retaining plate. replaced new seal and tightened screws.
This is a old 2000 side by side Kenmore frig bought from sears. left Freezer side was building up ice in the back, while right side was not cool at all. The Defrost Timer was behind the light panel on top in compartment side. Easily remove unit and unscrew things. Works like a champ.
Refrigerator is not cooling. Light and fan working. Changed the capacitor.. Still not cooling. Back to discovery mode.It may be the timer Certainly not PartSelect's fault. They have great service.
Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.
Shut off water and disconnected at factory joint at bottom hinge. Unplugged the electrical at the top hinge. Removed the door and installed new bottom hinge and cam assembly. Reinstalled the door and hooked water and electric back up. Part worked fine.
Cams on Hinge assembly broken, door didn't close properly
I supported door with 2* 6 scrap wood. I used cedar shingles to raise door to correct height. Using a socket wrench, I removed the hinge from the fridge and the cam assembly from the door. I installed the new hinge and cam using the shims thatwere behind the original parts. I removed the 2*6 supports and the door now works perfectly.
Refrigerator would begin to lose it's cool and we saw ice caking on the bacjk panel of the freezer section.
We had to empty the freezing section, remove the 4 screws that held the back panel and defrost the coils. Then with the diagram we got from the internet, we removed the defroster and easily installed the new one and put the back panel back on. We did find later that it was still icing over so I ordered the thermostat and we installed it today. It too was easy to install. We spliced the wires and hooked the new thermostat to the old wires and reinstalled the back panel. Hopefully this will solve the problem for us now.
When it was discovered there was a cooling problem in the refrigerator, I went to parts select web site and went through the troubleshooting section. Then I tested the defrost timer and the defrost element as directed by the web site. I then found out doing this, that is was the defrost timer. I ordered the part online and it was delivered THE NEXT DAY! I removed the bottom panel of the fridge, removed the screw holding the old timer, removed the wires, and reversed the procedure to install the new one. It has been 1 week, and everything is working great. Thank you PartSelect. I have since then recommended you to a relative who was having the same problem. Thanks again.
Fridge not cold & DE light flashing on status panel
Removed all the freezer shelves/trays. Removed screws top and bottom on back panel. Found coils completely frozen over. Used heat gun to completely melt all the ice. Found that the Defrost Heater actually includes a new Defrost Thermostat (unlike the service manual shows). Unplugged and unsrewed the old Defrost heater parts and unclipped the Defrost Thermostat. Installed the new parts, put everything back together, and returned the unneeded Defrost Thermostat for a refund. It's been working fine ever since.
1. Unplug refrigerator or flip breaker to kill power to the refrigerator. 2. With hands, gently pull the bottom lip of the 3" X 11" face plate panel above the dispenser head. 3. Remove the 4 screws that are under the removed panel. 4. Tip the assemby down to reveal 2 plugs. 5. Gently pull the 2 plugs to disconnect. 6. Open the assembly to reveal the solenoid. 7. There are 3 screws at the base of the solenoid. The center screw attaches to the green ground wire. 8. Remove the three screws. 9. Observe: The bracket at the top of the solenoid unit tucks behind a 4th screw above the solenoid. You may need to loosen this screw to relesae the solenoid. 10.Unplug the yellow and red connector to the solenoid. It should not be totally free to remove. 11. Put the plunger into the solenoid. Note that the plunger has an opening to insert the white plastic trigger for the trap door. Make sure the trigger is inserted into this opening before reassembling. 12. Plug the yellow and red connector into the new solenoid. 13. Position the new solenoid to match the screw holes. The bracket at the top of the solenoid tucks under the 4th screw. Tighten as necessary. 14. Insert the green ground wire into the middle screw hole at the base of the solenoid and tighten. 15. Insert the two screws to either side of the ground wire and tighten. 16. Gently reconnect the two plugs. 17. Tip the assembly back into place making sure the trap door and hoses are lined up correctly. 18. Replace the 4 screws. 19. Snap the face plate back into place. 20. Turn on the power and give it a try!
I used other instructions provided by customers on the website. They were very useful.
This is the second time we replaced this unit. The first replacement failed within the one-year warranty period. I called customer service and they had a replacement part and refund for the previous part on its way immediately. Excellent service!
Pretty much self explanatory.Removed drawer and anything on top of glass shelf.Remove two screws holding on slide.Replace with new slide.Repeat on other side.Replace shelf and drawer.