CSK27PFXEAA Hotpoint Refrigerator - Instructions

First I removed the two screws that held the old slide to the refer side wall, (after unloading the shelf and taking out the Veg. draw). I then put the screws in the new slide spots and screwed them into the refer wall using a hand screwdriver (phillips) and put everything back in place. It was about as simple a repair of anything I have had in the past 75 years. I didn't even have to swear.

The light shield is only held in with a single screw, so it was the simplest install ever - unscrew the old light shield (in my case, the remaining piece of the light shield), put the new shield in place, and screw it down. Doesn't get any easier than that.

The isnatalla tion was very simple, two screws, and that was it. The only problem was ttying to determine if it was the right side or the left side rail

Unplugged fridge.Removed 2 screws holding a panel. After panel removed took off old fan and inserted new. Quite simple.

First take all your junk off the shelf (with the broken rail of course), take the glass shelf off. Remove screws (phillips). Throw away old rail. Replace new rail, tighten screws. Replace shelf, replace junk. You're done.

I removed food from shelf over crisper drawer, then removed shelf and crisper drawer, removed two phillips head screws in right side rail and replaced rail.

Easy as 1-2-3

removed drawer, unscrewed old slide, screwed on new slide, voila! finished! I was very pleased with PartSelect -- ordering was easy, the correct part came quickly, and packaged very well. All of life should work so smoothly!

1) The large drawer is first removed from the guide that remained on the side wall.

2) Removal of the light shield from the rear of the glass shelf to facilitate glass shelf removal by lifting the rear edge of the glass and remove it.

3) Unscrew two phillips head screws holding the remaining pieces of the plastic guide to the interior side panel of the fridge.

4) Examine the replacement guide and insure that the nylon guide and stop parts are clicked into place. If unsure, look at the guide on the other side to ensure that both are present and completely seated before installation of the replacement guide. (These usually fall out of the guide during shipping and should be in the bag with the guide!)

5) Once the guide is outfitted with the nylon guides, secure the new guide with the two phillips screws and DO NOT over tighten, remember you are dealing with plastic guide and steel screws going into a steel cabinet.

6) Re-install the glass shelf, followed by the light shield and finally the large drawer which should slide out smoothly to the stop and back closed without any drag.

7) A successful installation usually includes giving the drawer and glass shelf a good cleaning that probably could be done to the entire fridge side of the unit.

I would recommend removing the dor first as I had to do this after fighting with the drawer to get it out.
There is a cap on the hinge that has one screw, then two nuts and the door is off. From there the drawer rails are easily replaced.

The drawer slide broke and I just removed the 2 screws that were still in the side of the refrigerator. I then screwed the new drawer slide in the same holes and it was done!! Simple, simple....even for me, the housewife.... ; )

This was so easy! I got the part number off of the broken part, ordered online, and it was delivered the next day!!! So fast! Then I just unscrewed the broken part and reused the existing screws to install the new one. It took about 5 min.

Thanks for making everything so fast and easy!

Turned water supply off; pressed dispenser sw to release presure ; cut tubing holding reservoir ; nuit driver to release screw holding reservoir and pulled out ; took outside and used hose nozzle to try to clear; did not clear at first then took weedeater string and disloged something and water flowed freely; turned out had to change waer solenoid valve (both) as the one for the water dispener was also plugged which did not show up before.
P.S. Had back flow water thru system before and changes of parts. Water flowed freely.

Took the drawer out, unscrewed 2 screws, replaced the part, put the drawer back in.

I removed the two screws from the old broken rail using a regular star screw driver and replaced the new rail you sent us. Took only 2 mints to do all.

I removed the old broken part and replaced with the new part. Simple as pie, my husband was so happy and impressed I had it done by the time he got home from work!!!!