CSK24GRXDAD Hotpoint Refrigerator - Instructions

really simple,take 2 nuts loose pull the hose out and then replace.took less than 30 minutes

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

This is a side by side freezer/refrigerator, nearly 30 years old. The repair was very quick and easy. 1. Remove two screws from top bracket. There is no cover for the top hinge on this older model. (2) Lift off door and set on kitchen table. (3) Remove two screws holding bottom door hinge. (4) remove two screws hold the cam and shims on the bottom of the door. (5) replace the broken cam on the door, and the bottom hinge assembly. (6) Replace the door on the bottom hinge. (7) Re-attach the top hinge screws, making sure the door is parallel to the freezer door. It took about 10 minutes to do all of the above. Best yet, I ordered the kit about 10am on a Monday, and the parts arrived, normal delivery, before noon the next day.PS- I used petroleum jelly to grease the hinge before replacing the door. The only tool I needed was a nutdriver.

I removed the old slide rail, and replaced it with the new one...in about 5 minutes! My drawers don't fall anymore! SUPER FAST shipping! I commend you...I ordered it one day, and it arrived the next day! Now THAT'S service! Thanks.

removed the inside fridge electrical panel and swapped switches

took the old gasket off. cleaned the area were the old gasket was,also cleaned the metal screwdown brakets. put the new gasket in hot water to make it easier to work with. then put the metal in place on the new gasket. place the new gasket in place on the door. then put 1 screw in the middle of the long sides, then did the all 4 corners. then only snug the rest of the screws at first. take your putty knife and slide it under thegasket to seat it squarely on the door. tighten and done.

I took off the front cover of the icemaker assembly and found that the gears were not meshing properly and therefore slipping. I removed the front panel and found that the white plastic cam unit under the large gear wheel had disengaged from the hole in the front plate which is why the gears were slipping. I refitted the cam and wheel and it worked fine but stopped again for the same reason the next day. As the plate appeared to be buckled somehow (not user repairable) and, as the unit was leaking and pooling water (which froze) in the collection unit, I decided to change the whole icemaker.

Ordered about 1300 on a Thursday, it arrived the next day at noon and was fitted straight away. As others have mentioned, the extension cable required to fit into my old fridge made it quite cumbersome however with a bit of juggling and persuasion, I got it to fit into the cut out corner of the ice container so it is completely out of the way. Job done in about 35 minutes, making ice in an hour.

Your Video really made it easy, showing the actual replacment of the part. However I did have one problem, which was I could not unplug the panel just by pulling on the plugs. A locking catch is on each plug so I just moved the panel out of the way.

Follow instruction on the video you provided

shimed the door up to its proper level. removed plastic cam from bottom of door with a socket disconnected the water line fitting and clamp. with a nut driver removed the hinge assy from cabinet being careful i sled the hinge assy off the plastic water line being sure not to kink the line, sled the new hinge assy back on the water line and mounted the new hinge assy to the cabinet and connected the water line back up and turned on the water and checked for leaks, all went well. place the bottom grill cover back on.

Easy to take apart just keep track of all your screws and parts most inportant of all are the 3 claw like and spacers that are inside the clear round part at the end of the ice bucket these pieces only turn in one direction if you put them on backwards or in the wrong order you will tear up your ice bucket so pay close attention when taking it apart and reassembling it. One think that might be helpful is to take some pictures of the ice bucket before disassembly something i wish i had done prior to taking it apart. Some people download instructions off the internet but i felt like i could do it with out help well good luck

Followed directions in your video. Very helpful. Be certain to pay strict attention to how old part is removed. Had a little trouble replacing door on lower pin/hinge. Helps to have a little assistance. Good suggestion from another customer: get the kit.

Removal was easy. The problem was that the old hinge had screws approximately 3/4 inch apart. The new hinge assembly had screws 1 inch apart. The threaded backing plate matched the 3/4 inch spaced old hinge but would not line up with the new one. There was a hole in the refrigerator frame but no way to hold the screw from the back. I had to fine a bolt and nut that would fir and still be heavy enough to hold the weight of the door. This repair took place at my cabin--miles from any hardware store. I found a long enough bolt and nut but it was a little too big for the hole in the hinge. I had to drill the hole in the hinge out so it would fit. Trying to reach the back of the bolt with a nut was a problem. I used tape wrapped backwards on my finger to hold the nut and then reached around to start the bolt into the nut. It too a few tries but I finally got it. Bottom screw was not a problem. It took about an hour and a half to fix the door but it works fine now.

The video on the GE site was great. Showed step by step instructions on how to remove the old ice maker and install the new one. Also helpful was the detail on the water chute which needed to be moved from the old ice make to the new one. Saved hundreds of dollars by not having to have a repairman do this work for me.

The part broke on Sat, my husband was out of town..I decided early Sunday morning to research the parts. I found partselect through my google search, just loved the site...very easy to locate the parts I needed...watched the video and decided I could fix it myself. Two days later I received the parts and it took me about 20 minutes to make the repair ..it was such a good feeling to know that I did it myself...I did not even have to rely on my husband ...love ...love...love this website!