CSK22GAZAAD Hotpoint Refrigerator - Instructions

Removed door off hinge , remove bottom hinge, drill out rivet, lift off old cam & replace with new cam ,add new 1/4' BOLT(NOT SUPPLIED) to location where rivet was, reinstall bottom hinge & door ,check alignment, works perfect.

Thanks

Placed blocks under the refrigerator door to take weight off the lower hinge pin. Removed the hinge by removing two screws into the refrigerator and two screws into the bottom of the door itself. This allows the hinge to be removed so the old nylon "closer" pieces can be removed (the one attached to the refrigerator has a rivet holding it in place so that has to be drilled out and replaced with a 3/16 inch bolt and nut). After re-attaching the nylon "closer" to the refrigerator side of the hinge and placing all the shims back in place, I re-attached the hinge to the door first, then the half hinge to the refrigerator. Had to line up the holes, tighten the screws and presto, the door closes like it was new again.

The freezer door side is more difficult as there are wires and a water line to work around.

This one is a no brainer… One Phillips screw on top to pull top door hinge trim. Two nuts and the top hinge is free. Then pull the door… it helps if you unload all the crap in the door bins. Remove the remnants of the door cam and that leaves a pop rivet. Put some vise grips on the head and use a hacksaw to remove the lower part of the rivet. Then pop-rivet the new door cam in place. If you don’t own a pop-rivet tool, I guess you could use a 10/32” screw and nylock. Plop the door back on and you’re done. Took all of about 15 minutes.

Really simple, I used a can of soup and a small piece of wood set under the door, and tapped it tight with the hammer to hold it in place while I removed the hinge. Two bolts at the bottom and two under the door itself. Installed the new hinge set, bolted tight and removed the shim.
The whole thing took less than 5 minutes

1st I unscrewed the side rails after I removed the drawer. I saved the screws and both rails until I received the new ones.There were 2 screws in each side. 2nd I looked online at the parts select web page. The exploded diagrams were extreemly helpful. Like most people my appliance book does not have this feature. I ordered the 2 rails for the drawer on Sunday morning and the parts were here by Wednesday afternoon..very good service in my opinion. I then proceeded to replace the two side rails with the screws that I saved from dismantling them. I then put the drawer back into the refrigerator and it worked perfectly. This repair was easy and it saved me a $60.00+ dollar service call and a longer wait period to get the repair done! I will continue to use part select.com for all my appliance repair work. Thanks

BUY TWO CAMS! Just like the others, both of the cams were shot. My husband & I did this ourselves & have NEVER attempted appliance repair before.
We propped the door up high enough to access the bottom hinge piece on the fridge & removed using socket. Removed the cover from the top hinge. Slid door down off the top hinge in able to get to the cam on bottom of door. Replaced this cam 1st in order to get door back on while worked to get the old cam off hinge. As others posted, this is rivited on. Used grinder to grind off rivit & hammer & punch to punch out. Attached new cam with bolt & nut found in our tin of leftovers. Inserted hinge into door & reattached to fridge. DONE! Not hard at all & didn't even argue the whole time.

Unscrew the two screws with a screwdriver and replace the new slide rail with the same screws.

I took out the drawer and the glass shelf.
All that was required after that was to unscrew the old part and replace it with the new one using the old screws. Very easy!

I used a short Phillips screwdriver to remove 2 screws that held the broken left slide rail in place. Then I screwed the new part in place. Really, really easy!

I removed the 2 screws that had held the cracked drawer slide rail. The new slide rail fit perfectly. I screwed it in using a phillips head screw driver and the drawer slid back in place. Very easy!

Removed four screws at bottom of door, while someone held the door in place replaced the upper cam (there are two) applied some silicone plumbers lube between the mating surfaces and tightened it up. Works like new bottom cam was only slightly worn. P.S. Remove everything from the door first.

I removed the old broken part and replaced with the new part. Simple as pie, my husband was so happy and impressed I had it done by the time he got home from work!!!!

1) The large drawer is first removed from the guide that remained on the side wall.

2) Removal of the light shield from the rear of the glass shelf to facilitate glass shelf removal by lifting the rear edge of the glass and remove it.

3) Unscrew two phillips head screws holding the remaining pieces of the plastic guide to the interior side panel of the fridge.

4) Examine the replacement guide and insure that the nylon guide and stop parts are clicked into place. If unsure, look at the guide on the other side to ensure that both are present and completely seated before installation of the replacement guide. (These usually fall out of the guide during shipping and should be in the bag with the guide!)

5) Once the guide is outfitted with the nylon guides, secure the new guide with the two phillips screws and DO NOT over tighten, remember you are dealing with plastic guide and steel screws going into a steel cabinet.

6) Re-install the glass shelf, followed by the light shield and finally the large drawer which should slide out smoothly to the stop and back closed without any drag.

7) A successful installation usually includes giving the drawer and glass shelf a good cleaning that probably could be done to the entire fridge side of the unit.

I would recommend removing the dor first as I had to do this after fighting with the drawer to get it out.
There is a cap on the hinge that has one screw, then two nuts and the door is off. From there the drawer rails are easily replaced.

I removed the drawer and broken piece, then I screwed in the two screws to put the new piece in place. I then had trouble putting the shelf back in place due to the piece being a little bent. I loosened the front screw and was able to manuver the shelf in place with a little force. The new bracket works great.