Models > CSE9000BCB > Instructions

CSE9000BCB Maytag Cooktop - Instructions

All installation instructions for CSE9000BCB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSE9000BCB
46-56 of 56
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

burner bad

  • Customer: Edward J from Baxter MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
looked it up on line how to change it. before I ordered part, to see how much of a job it was. was real simple to change, had no problem. also part select sent the correct part. Job went well

front burner would not heat

  • Customer: Jack A from Biloxi MS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
simply took off smooth surface top flipped it upsde down on a towel. unbolted the entire burner assembly. matched connections with the new burner with limit switch. replaced smooth surface top plugged it in. no problems. extremely easy fix no repair charges.

Small burner on glass top stove stopped working.

  • Customer: REX from VIRGINIA BEACH VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First, the diagram on your website said remove two screws. The diagram looked like they were on the back of the stove on each side. On my stove there were three screws that were visible under the front lip upon opening the oven door. I removed the top, which comes completely off and set it aside. Be careful when removing the top. Don't drag it out, otherwise you'll tear up the asbestos around the other burners. Two people would be better for the inexperienced people. The new elements have been redesigned, so the diagram doesn't fit what you are looking at. Plus, the diagram on paper is looking underneath the element when you are looking down on the top of the element. I removed one wire and put it in the same spot on the new. Turned out it was not the element that was bad. It was a loose wire in the inside of the control panel.

Surface element was out

  • Customer: Veronica from Midlothian TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnect the power.took the cooktop off the range. Turned it over. Removed the underside plate. Disconnected the bad element. Pluged inthe new element. Replaced the under plate. Reconnected the range to the stovetop .put cooktop in place. Reattached screws. Turned on power. Worked perfectly.

The front left side burner was broken.

  • Customer: Yelena from San Francisco CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
We lifted the glass top, uninstalled the old burner and installed the new burner in it's place. It worked right away - and is still working. No other tricks the new burner was a perfect fit.

Hotplate not working

  • Customer: Anthony from Louisville KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two screws holding cooktop to oven. Unlike the video, the cooktop was not detachable as the wires were hard-wired to the range, so I had to prop the top up with a 6" block of wood and was working upside down. I replaced the element and everything worked just fine.

Small Surface Burner Was not Working

  • Customer: Tevfik from Naugatuck CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Repair video was very helpful. I have removed the screws on both sides of the appliance under the surface plate, in the front. The Owen door has to be open for that. Then I have pulled the surface plate for a little space to disconnect the two connectors. Turned the surface plate over on the kitchen table, removed the 6 screws. Turned the burners assembly over and removed the small burner by disengaging the two clips. I have removed the 2 clops from the burned burner and assembled it to the new burner. I have placed the burner and engaged the 2 clips with a crownose players. I have removed one electrical connecter at a time and connected to the new burner. I have turned over the assembly over the glass plate and assembled the back cover with 6 screws. Put the surface plate on the range and connected the 2 connectors, pushed back, lined it up with the 2 screw holes in front of the range on bot sides and put the 2 screws in and Finished.

cleaner

  • Customer: Mary from Duarte CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

Front burner burnt out

  • Customer: Leonard from Kansas City MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
THIS JOB REPLACING THE WAS SO EASY, IT TOOK ABOUT TEN MIN,TO DO IT THANKS

The left rear burner had stopped heating.

  • Customer: Louis from Morgan TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. I ordered a replacement heater element from Parts Select, which arrived in just 3 days at my home. 2. I turned off the main circuit breaker to the range. 3. There are two small sheet metal screws inside the top left and right side of the oven door frame which need to be removed first in order to lift and remove the burner top from the range. 4. After lifting and pulling the burner top toward me about 6 inches, I unplugged the left and right burner assembly wiring harness connectors. 5. I lifted the burner top assembly off the stove and turned it upside down an a table. 6. There are six sheet metal screws that need to be removed to allow the sheet metal panel holding the heater assemblies to be lifted off and then also set upside down on a table top. All five burner elements are now visible. 7. Disconnect the slip-on electrical connectors to the specific heater assembly that is defective. 8. Unscrew the three small sheet metal screws from the three spring clips that support the heater assembly on the sheet metal panel; re-attach the spring clips to the new heater assembly. NOTE: Either memorize or record the position numbers that are cast into the ceramic housing of the burner to replace the new burner in exactly the same position. 9. Insert the three spring clips back into the sheet metal panel where the old, defective burner assembly had been removed. 10. Re-connect the slip-on wire clips to the new heater assembly in the same position as they were removed from the defective heater assembly. 11. Turn over the sheet metal panel with the burner assemblies attached and replace the sheet metal screws holding the panel to the stove top. 12. Turn over the stove top assembly and set back onto the range allowing space to reach to the back and re-connect the polarized connectors to the left and right side burners. 13. Slide the stove top back to the rear and carefully lower the front edge back down with the two metal tabs inserted back into the oven door frame. 14. Re-install the two sheet metal screws that hold down the stove top. 15. Turn on the main circuit breaker to the range. 16. Carefully test the new heater assembly by turning the range control knob to LO heat and watch for the stove top burner to momentarily turn red with heat. 17. Turn off the range control knob. 18. You are finished. It was a very easy installation.

Surface element with limiter 6", 1200W was burned out

  • Customer: Tevfik from Naugatuck CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the two screws, on both sides of the oven wall corner. Gently lift the front end of the glass top and pull towards me and disconnect the two electrical sockets. Carried the glass top assembly on the kitchen table and turned upside down. Removed the six screws. Removed the assembly from the glass top. Turn the top burners assembly over and disengaged the two clips of the burned out burner from the assembly plate. Transferred the two clips to the new burner on the exact locations like the old ones were. I have placed the new burner on the location and snapped the clips on the slots. Removed the connectors one piece at a time and connected to the new burner. Reversed the previous disassembly and all was done Works like a charm. Thank you all for assisting me in providing the necessary parts and video instructions. It was a lot cheaper than to buy a new range.
All Instructions for the CSE9000BCB
46-56 of 56