Models > CSE9000BCB > Instructions

CSE9000BCB Maytag Cooktop - Instructions

All installation instructions for CSE9000BCB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSE9000BCB
16-30 of 59
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

RIGHT SIDE REAR BURNER NOT WORKING

  • Customer: WILLIAM from TAMPA FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
ONLY HITCH I EXPERIENCED WAS IDENTIFYING THE CORRECT REPLACEMENT. THE ORIGINAL DIAGRAM PRESENTED THE ACCURATE SHAPE OF THE ELEMENT MY RANGE REQUIRED. HOWEVER A DIFFERENT SHAPED ELEMENT WAS DISPLAYED WHEN I NOTED MY UNIT IS A SERIES 12 SERIAL NUMBER. I ORDERED IT (WITH RESERVATIONS) AND AS IT TURNED OUT THE REPLACEMENT WAS IDENTICAL TO MINE. NEXT TIME I WILL HAVE A LIL MORE CONFIDENCE IN THE INSTRUCTIONS GIVEN.

Element quit working

  • Customer: Daryl from Oak Creek WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Important to unplug the appliance first. There were two screws which were at the top opening of the oven. They were a bit obscure, but with a bit a searching, I was able to find them. After removing those two screws, the entire top lifted up. There were four screws from the bottom of that assembly which were easy to find, and once removed, the top lifted of easily. I found it easier to remove the two power lines with two easy disconnects, this made it easier to work on the assembly. The element itself was held down by two simple clamps which required no tools. There were four easy to remove wires, and the element came right off. Simply reversing the process put it right back together, plug it in, and back to cooking again.

Burnt out burner

  • Customer: John from Clermont FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
Had this range for 6 years. My daughter turned on the burner and it went "pop". She was very upset. I found the best price at PartSelect, and ordered the same day.

the first burner arrived broken in the box. We contacted PartSelect, and they immediately sent another and rushed shipping. It arrived in excellent condition.

To replace the unit: First, I turned off the circuit breaker for the range. Then I removed the two Philips screws that held the cooktop down. Next I removed the nut screws holding the burner to the cooktop.

Then I placed the new burner next to the old one, and one by one swapped the wires (this way I was sure I had the right wire on the right connector). One of the wire connectors broke when removing it from the old burner. PartSelect had provided 4 repacement connector pieces (oddly, all of which were too small for the burner element). So I located a replacement connector at a local hardware store. Stripped the end of the wire and used pliers to fasten the new connector.

After all connectors were secured to the new burner, I screwed the burner to the cooktop, then closed the cooktop and secured it with the two screws.

Turned on the circuit breaker, and it works like new! Saved over $100 by doing it myself!

left rear burner not working

  • Customer: Brice from Spotsylvania VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
I ran numerous tests to eliminate the on/off switch and to ensure the wires were not defective. Thus I came to the conclusion it must be the burner was defective. I ordered the part from parts.com. I received the part in less time than what was advertised. The part arrived in good condition. I placed the part in and it worked just like new.

Thank You

The left rear element failed

  • Customer: William from San Diego CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 2 people found this instruction helpful
First , I turned off the circuit breaker to the oven.
Next, I removed the two screws at the front of the range top and slid the top out until I could disconnect the multi-plug connecting the wiring harness to the stove.
I then took the entire top out to a table and set it upside down. It was easy to unbolt and disconnect the lead to the element. One of the leads was burnt, so I had to replace it. I slid the new element into place, bolted it down in the same orientation as the old one and reconnected the leads.

I slid the entire top back into place on the range and re-installed the securing screws. Then I flipped on the circuit breaker and turned the element on.
Success! Perhaps I didn't really need to change the element since the burnt lead was the cause of failure. But its good to have a new part installed anyway.

Rear 8 inch element was not working

  • Customer: PAUL from SCOTTSDALE AZ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
Removed two screws bottom front corners of range top - propped the top up - removed the wires from the element - removed the old element - installed the new element reattached the wiring reattached the hold down screws and bingo it worked!

First thing to do is turn the 220volt electrical circuit breaker to the unit off and the last thing is to turn the breaker back on!

INDICATROR LIGHT FOR 6" BURNER QUIT WORKING

  • Customer: NANCY from LITTLETON CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 5 people found this instruction helpful
OK this is a glasstop Jenn Air cce3531B, 5 burners, 11 years old. I am computer data entry employee and 56 years old. I have never done repairs myself in the past but decided to try. I ordered a new burner and indicator light as I wasnt sure which to replace. I found the main breaker and shut it off. I lifted the stovetop out of the counter opening by pushing it through the bottom and placed it on the counter with a towel under it, I had plenty of room to work so that was very easy. I used a nutdriver set to remove 12 screws and lifted off the top very carefully and placed it in the other room , since i had to repair unit thought I would also clean and replace the foam tape around the perimeter of the glasstop. Ok now I unscrewed 4 more screws with the nutdriver and replaced the indicator light, that took about 6 minutes so far. Then I turned the breaker back on and tested and it did not work. Turned breaker back off ,now I replaced the burner by lifting it out of the opening very easily, unscrewed with philips screwdriver 2 screws and the new burner was exactly the same as the existing one so I just slid the old connections off one at a time and replaced them as I went along onto the new burner, screwed it back into place and turned the breaker on and tested it and it worked. I now turned the breaker back off and took off the old foam tape from the glasstop and replaced with new, fit it back onto the base and screwed the 12 screws back in and placed it back into the counter opening and turned breaker back on and now all is fixed and I saved $100 dollars in labor fees. This took 35 minutes and was easy for me. THANKS YOU PARTSELECT

BURNER ELEMENT REPLACED

  • Customer: GLENA from CINCINNATI OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
MY GRANDSON, AGE 15 DID THE REPLACEMENT. NOW, HOW EASY IS THAT!

Burner Out Glass Top Range

  • Customer: John from Monroe Twp NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
Just as others said. Remove top holdown bolts with nut driver. Prop range top up.
Use a pair of plyers to remove wires (make sure you have a diagram to restore).
Use screwdriver to remove element hold down spring and wire holder. Replace element and replace wires and screws.

back R burner of ceramic top stove went out - died

  • Customer: gayleana from spokane WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
1st - UNPLUGGED appliance from electrical source!! then removed screws to open ceramic stove top, disconnected wires from dead element, plugged in wires to new element, closed stove top, turned on burner - it worked!!

only problem is that "hot burner indicator" does NOT stay lit after burner is turned off!

Burned out stove top element

  • Customer: rick from colorado springs CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 4 people found this instruction helpful
Unplugged the power cord first. Opened oven door and removed the two screws that held the stove top glass down. Lifted the glass top and removed the four wires connected to the element. I taped the wires to the lid in the pattern they were attached to the element. remove the element from the brackets. The new element was an exact match. reversed the sequence. Put a pot of water on and boiled a hot dog! Perfect! Great part and speedy delivery!!

One of the electric stove top elements had burnt out

  • Customer: Anthony from Palmyra VA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on the new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.

element or temperature sensor failed: not working

  • Customer: David from Mary Esther FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.

Element Burned out

  • Customer: Buford from Sun City Center FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2 of 5 people found this instruction helpful
looked for how to video on you tube. It saved me lots of money. Anyone could do it.

Elements burned wouldn't heat

  • Customer: Jaime from Deltona FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 6 people found this instruction helpful
First I cut electric power off removed the two screws that hold glass top lifted up and removed two screws that hold element in place. I disonnected the wires and then pulled the element out
All Instructions for the CSE9000BCB
16-30 of 59