CSD2610KRW Magic Chef Refrigerator - Instructions

Simply replaced cover by hand. No tools required.

Move refrigerated and turn off water and unplug elect. Remove ice Ben and guide on right side. Move one screw on the bottom and lousen tow screws on top. Remove ice maker to unhook electrical connection. Transfer parts from old one to the new one . Revise the removal of it and when done .Plug in cord and turn on water. If you have done everything very carefully you will have ice in a few hours.Good luck.

Pried out the old switch with small screwdriver, popped in the new one and tah-dah!! ..the light came on. While I was at it, I cleaned out the freezer :). I cannot begin to imagine what a repairman would have charged for this.

Received the hinge and it took only minutes to hang the refrigerator door.

This was an easy fix. Just pull off the old gasket and press the new gasket in place.

The video of the repair is a helpful guide, but my refrigerator has the compressor very close to the condenser fan motor. With the compressor comes the copper tubing that is all in the way. I had to carefully bend them now and then to allow me to get my hands in position. The how to is easy, but the working with tools in cramped quarters was difficult. I think my Maytag side by side model makes for this job to be difficult, maybe yours may not be so bad. I took a couple of hours to complete. After the first hour, I covered the bare wires, and plugged the frig back in so it could do some cooling. I placed a small in front on the condenser to blow across it. Had a little break, then finished the job.

Ordered the correct replacement part (Icemaker Auger and Crusher Blade Assembly) as found here at PartSelect.com. Part was delivered within two days. Removed two screws to remove the old assembly; inserted new assembly, replaced the screws and problem fixed. Couldn't be easier.

Removed old auger unit by removing two screws - installed new auger unit by replacing the two screws. Easy schmeasy!

1.Lift out the ice bucket. 2.Remove two screws at bottom. 3. Remove front (made up from parts 20 and 21 in diagram by lifting the plastic flanges at the bottom and sliding it off upwards. Fingers were adequate to lift the flanges. 4. Remove the mechanism. It comes right out. 5. Slide the mechanism into the new bucket. 6. Put the front onto the new bucket by sliding down and lifting the flanges over the ridge at the bottom of the bucket. 7. Put the two screws in at the bottom. 8. Slide the bucket back into the freezer. This was the easiest repair I have ever done.

Based on comments I read at this web site, I first ordered the water valve; that did not fix the problem. Replacing the icemaker did fix the problem. It was easy to replace. Contrary to the instructional video, I couldn't simply tilt out the icemaker at the bottom after removing the lower screww; I had to loosed the two top screws as well. The leak was caused the coating on the icemaker being cracked and peeling.

I watched the video which gave me confidence that I could do the repair which I did in very little time. One thing to emphasize though: When you remove the vertical wire connector from the back of the freezer compartment, remember which color wire is on the top. I needed to watch the repair video a second time to be able to make that determination. Probably the repair video should have mentioned keeping track of that connector regarding the re-connection of it because it could also connect when turned 180 degrees.

I watched a youtube video and completed the repair in less than an hour from start to finish and save myself a service charge. It was fairly easy, the only problem was that it was a bottom freezer and getting to the ice maker was harder than if it was a side by side or top freezer.

I have an Amana freeze and I followed the procedure in the video. Which is very good! However on the Amana Model there two slight differences in the procedure that I felt I needed to do. The first one is, the condenser fan bracket is attached to the Freezer chassis with 4 screws, not three. The removal and installation of the back screw by the fan is a bear. I removed the other three and it allowed me to rotate the fan slightly to get more access to the fourth and did same on installation by just starting the 4th screw and then tightening it later. The second issue was my new fan hit the housing when I spun the fan. When I looked at the old one. It had a phenolic washer, between the fan and motor which spaces the fan out about a washer thickness from the motor. When I tried to remove the old one it broke in four pieces due to age. So, I made my own with a washer that I super glued to the motor housing after carefully centering it on and clearing the motor shaft . Seemed to work with out any more noise or balance issues...Thanks, your delivery was blindly fast and video was great!

I used the video on your website. It made me feel very satisfied that I was able to do it myself!

I unplugged the fridge. Then I removed the ice bucket. Then I removed the ice maker using a 3/4 socket to separate the connections and then used a small screwdriver to separate whatever connections were left. Then I installed the new ice maker and checked its level. Everything now works fine.