CSD2325ARB Magic Chef Refrigerator - Instructions

Followed your video instructions and tips. Real easy

Getting the old ice maker out was not difficult - it sits on a small ridge built into the freezer and then it takes three screws to attach it to the side of the refrigerator. Three important things to remember: (1) take off the metal bar that shuts off the ice maker from the old part, the new part doesn't come with the bar; (2) keep the screws and the cap from the old ice maker as they don't come with the replacement part either; and (3) make sure you put the water tube back into the holder otherwise it will pour all over the freezer (and not into the ice tray).

unplug refrigerator, take backing off with nut driver. Pull old blade off and put new blade on. Put backing back on and plug in.

Move refrigerated and turn off water and unplug elect. Remove ice Ben and guide on right side. Move one screw on the bottom and lousen tow screws on top. Remove ice maker to unhook electrical connection. Transfer parts from old one to the new one . Revise the removal of it and when done .Plug in cord and turn on water. If you have done everything very carefully you will have ice in a few hours.Good luck.

First Remove ice holder, now take out nut left side under tray, remove tray from mounts, unplug wires, remove tray from freezer, remove solenoid assy from tray try to keep it from coming apart, remove motor from tray, the auger yoke is on a shaft that has to be removed by turning it clockwise (reverse threads). i used a small Chanel lock to hold shaft when removing yoke, Now remount the motor and yoke, remount the spring loaded solenoid assy, slide the ice bin enclosure back in a ways, then reconnect the wiring harness, remount it rest of the way in, install the nut. and your good to go.

Had to replace ice bucket rack because auger motor broke the plastic backing and also the auger motor because shaft was bent on old auger motor. Just followed directions on web site to do repair.

Stopped by a local repair shop to buy a crisper glass shelf for my Maytag refrigerator. Maytag does not sell the glass shelf, looked online and saw Repacements Parts.com. Ordered the shelf. Very happy customer!!!

Based on comments I read at this web site, I first ordered the water valve; that did not fix the problem. Replacing the icemaker did fix the problem. It was easy to replace. Contrary to the instructional video, I couldn't simply tilt out the icemaker at the bottom after removing the lower screww; I had to loosed the two top screws as well. The leak was caused the coating on the icemaker being cracked and peeling.

I watched the video which gave me confidence that I could do the repair which I did in very little time. One thing to emphasize though: When you remove the vertical wire connector from the back of the freezer compartment, remember which color wire is on the top. I needed to watch the repair video a second time to be able to make that determination. Probably the repair video should have mentioned keeping track of that connector regarding the re-connection of it because it could also connect when turned 180 degrees.

I watched a youtube video and completed the repair in less than an hour from start to finish and save myself a service charge. It was fairly easy, the only problem was that it was a bottom freezer and getting to the ice maker was harder than if it was a side by side or top freezer.

I have an Amana freeze and I followed the procedure in the video. Which is very good! However on the Amana Model there two slight differences in the procedure that I felt I needed to do. The first one is, the condenser fan bracket is attached to the Freezer chassis with 4 screws, not three. The removal and installation of the back screw by the fan is a bear. I removed the other three and it allowed me to rotate the fan slightly to get more access to the fourth and did same on installation by just starting the 4th screw and then tightening it later. The second issue was my new fan hit the housing when I spun the fan. When I looked at the old one. It had a phenolic washer, between the fan and motor which spaces the fan out about a washer thickness from the motor. When I tried to remove the old one it broke in four pieces due to age. So, I made my own with a washer that I super glued to the motor housing after carefully centering it on and clearing the motor shaft . Seemed to work with out any more noise or balance issues...Thanks, your delivery was blindly fast and video was great!

I used the video on your website. It made me feel very satisfied that I was able to do it myself!

I unplugged the fridge. Then I removed the ice bucket. Then I removed the ice maker using a 3/4 socket to separate the connections and then used a small screwdriver to separate whatever connections were left. Then I installed the new ice maker and checked its level. Everything now works fine.

Repair was relatively easy. I found several videos on You Tube on repairing or replacing Solenoid & Ice Maker Auger Motor. They weren't broken but those videos show how to replace them and remove ice enclosure, which was the part broken. Only issue was removing yoke off the motor. It has reverse threads and videos had shown holding shaft of motor with needle nose pliers to hold it while you thread off the yoke. You need good needle nose pliers with teeth on them or the shaft will slip in them. I had to go buy new pair while repairing. It's all goes back together perfectly! I took pictures of the assembly, before I removed everything and needed to refer back to them when I was reconnecting the wires.

I pulled the dispenser bin and emptied the existing ice (the maker worked, the dispenser would not dispense). Though there appears to be more, there are about 4 (reciting from memory)very small tap screws holding the front of the dispenser unit to the bin. The dispenser activation screw mounts over protruding items at each end. The item at the back (away from the dispenser gear package) is the drive ring that was broken. The drive ring is a small plastic cup that inserts into an opening at the back of the bin (female side to the rear) and slides into the distal end of the activation screw on the same end. One must line up the small slot on the inside of the drive ring with the end of the screw. Slide the assembly together (make sure that the cube/crush switch rod is properly clipped in place with the return spring hooked to the clip), GENTLY install the 4 or so screws and return he assembly to the freezer. It should work flawlessly. Elapsed time: 15 - 20 minutes.