Models > CSC22GRSAWH > Instructions

CSC22GRSAWH Hotpoint Refrigerator - Instructions

All installation instructions for CSC22GRSAWH parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CSC22GRSAWH
811-825 of 855
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice/Water dispenser freezing/clogging

  • Customer: Barbara from Pasadena TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the Video on your website and that made it so easy and simple to follow. Thank you!

Ice machine flapper door solenoid burned up

  • Customer: Troy from Tullahoma TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Follow PartSelect video on website, had no problems learned a lot

ICE SHUTE FLAPPER WAS DISTORTED AND DID NOT SEAL OPENING CAUSING FROST BUILD UP

  • Customer: DON from ZELLWOOD FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
REMOVED CONTROL PANEL BY INSERTING SMALL SCREWDRIVER IN THE 3 HOLES UNDERNEATH TO LOOSEN. REMOVE 4 SCREWS HOLDING CIRCUIT BOARD . UNPLUGGED 3 CONNECTORS. REMOVING CIRCUIT BOARD GAVE ACCESS TO FLAPPER. REMOVED FLAPPER BY UNCLIPPING. INSTALLED NEW FLAPPER AND REVERSED DISASSEMBLY PROCEDURE. THIS WAS 2ND TIME IN 2 YEARS I HAD TO REPLACE THIS PART.

Frost buildup in the freezer near the ice chute.

  • Customer: Brenda from Little Elm TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video on the PartSelect.com website and decided to give it a try. The replacement of the flapper was even easier than I anticipated! The old flapper was extremely warped and was allowing air into the freezer. I'm not sure how/why it was in that condition but I am happy to report that I have no more ice buildup. Thank you, PartSelect!

Frost in ice dispensor

  • Customer: David from Saint Johns FL
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Had to take front panel off dispenser area. Then remove components and install new part. That was easy part. Problem was getting components back into front of freezer. Seemed like something was blocking it from going all the way in. Had to remove small amount of insulation and "jiggle" components and eventually fell into place.

Inside freeze was frosting up

  • Customer: Dennis from Glendora CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
used a flat screwdriver to pop off out side cover then remove 6 screws took off plate. Pulled off the flapper and replaced. less the 15 mins and fixed the issue

3rd Flap for this Ice Mkaer, keeps warping

  • Customer: Robert from Fripp island SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very Easy, follow direction I the video.

air leak from ice maker flap permitting frost buildup inside ice maker dispenser

  • Customer: Jack from Ft Myers FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched à video provided at your website. Removed te cover then removed 4 screws holding the control panel' snapped out the old flap and inserted the new one.

The rubber seal on the flapper came off.

  • Customer: Wanda from Katy TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My husband made the replaced the flapper while watching the video provided in your email, it was easy. Thank you.

Frost in and around ice maker outlet

  • Customer: Harold from Concord CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the video directions. Spent about 5 minutes and I was done. Very easy to do. Problem with frost is gone. The video makes it easy to remove the plastic parts without any damage.

Not clear instructions

  • Customer: Jady from Thornton CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Common sense will take you thru the process of removing, then just reverse the process to replace the auger.

REPLACEMENT OF ICE MAKER

  • Customer: Craig from Eagle CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed old ice maker, then screwed in new ice maker. Only thing that was a little difficult was to hold the auger motor, while trying to unplug the clipped in plug on the old ice maker. I could have used an extra pair of hands.

No problems.

  • Customer: Patricia from Norwood NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took out the old, replaced with the new. Needed second person to hold the flash light. That is the secret to get it plugged in and secured.

Frig was not making ice.

  • Customer: robert jr from east rutherford NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed the faulty ice maker in about two min.. New unit was installed in approx. five min. Watched your video prior to installation and it helped greatly.

Icemaker stopped making ice

  • Customer: James from North Billerica MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I just followed the directions carefully, loosened the screws with a nutdriver removed the unit from the screws, unplugged the unit from the freezer plug, took out the new unit, used the adapter supplied with the unit to match up with the plug in the freezer, carefully attached the icemaking unit to the screws, carefully slid the cord behind the unit, lightly clinched down the screws, checked it with a level and then did the final snug down. turned the unit on and it worked fine. Pretty easy, just take your time, don't rush and it will come out fine.
All Instructions for the CSC22GRSAWH
811-825 of 855