Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CGR1420BDW > Instructions

CGR1420BDW Magic Chef Range - Instructions

All installation instructions for CGR1420BDW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CGR1420BDW
61-75 of 226
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

range burner igniter not functioning

  • Customer: Patrick from Greeneville, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 11 people found this instruction helpful
Removed grill and set aside, then removed burner with a 1/4 counter clock twist. Removed ground wire and igniter wire from burner. Set to side in order taken off. Remove the two screws on the panel that is on the back of the unit and slide it up and set it aside. Removed screws from side decorative panels each side (one top and one bottom) and slide panel toward the rear to remove from notch slot. Then removed the two screws on each side and back to remove top of range. On the side there are two screws together towards the rear, the one towards the front of the range need to be removed. Then removed four screws that held the pan under the range top that were screwed into the gas line supports. Then removed the two screws from rear that held the pan in place. Remove the pan and set aside. Lift the right gas line burner support up. Remove ground bottom, hot wires upper and igniter wires from spark module. Pop module out and replace with new one. Reverse process to complete repair. Cause that the wires do not get under the pan when reinstalling same

Oven would not maintain set temperature.

  • Customer: Charles from Hardy, AR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 2 of 2 people found this instruction helpful
1. Closed gas valve at stove supply outlet.
2. Unplugged stove electrical connection
3. Unplugged electrical connections to defective valve
4. Removed 4 screws on burner side of heat heat shield
5. Disconnected gas inlet to defective valve
6. Removed 2 screws holding valve retainer to bottom of unit
7. Lifted gas burner inlet tube while pushing valve toward rear of unit - - - (a bit tricky)
8. Removed valve from rear by tilting forward so valve outlet clear the burner inlet tube and heat shield. Heat shield is not removed, but must be raised enough to allow passage of the valve outlet protrusion.
9. Installed new valve by repeating the preceding steps in reverse.
10. Reconnected gas and electrical, and checked performance

Bad Gasket

  • Customer: javier from Santa Ana, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
I just twist the burner, pulled it out, disconect the two wires. Reconect the wires to the new burner and placed back .

floor panel heavily stained and warped

  • Customer: Joel from Monroe, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
slide latches in rear of floor panel forward and remove.

Oven would not maintain temperature

  • Customer: David from Fresno, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 3 people found this instruction helpful
First I removed the oven racks, then the bottom cover over the burner. I then unscrewed the two screws holding the igniter on to the bracket on the burner tube. I then removed the storage drawer and loosened the two screws holding the metal shield in place. I then unclipped the electrical connection to the ignitor and pushed it up past the insulation. I then went back into the oven and pulled the wires and connector through. The old igniter was out!

Installation of the new one was just as easy. Screwed the new igniter onto the backet, stuck the electrical connector through the hole in the back of the burner tube, and connected it. I then replaced the shield and the storage drawer, replaced the bottom pan over the burner tube and the racks. The stove works perfectly and my wife is happy. The job couldn't be easier.

Replaced burner

  • Customer: Ramiro from Bernalillo, NM
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 2 of 3 people found this instruction helpful
Went well

corroded burners

  • Customer: Daniel from Can Francisco, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench (Adjustable)
  • 2 of 3 people found this instruction helpful
Unscrew the burners an install new ones! Anyone could do this.

cap on the burner broke off

  • Customer: Marcia from Bronx, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 2 of 4 people found this instruction helpful
My husband simply twisted out the old burner with a pliers and attach the new burner. Simple and easy....

ignitor went out

  • Customer: Horacio from La Habra, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
one screw holds the cover to the connector. one screw for the burner tube to the oven frame. two screws hold the ignitor bracket/assembly to the burner tube. that's it. take four screws off and disconnect. connect and put four screws back on.

Oven wouldn't heat

  • Customer: Becky from Bussey, IA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Removed oven door by opening slightly and lifting straight up. Pulled out racks and removed bottom of oven. Unscrewed wingnut and removed burner shield. Removed 2 screws that hold igniter and unplugged the connection. Reverse the procedure to put it all back together.
Be patient, it takes a few moments for it to begin heating when you first turn it on.
So easy a woman can do it ! I know,(I am one).

Oven heated very slowly

  • Customer: Thomas from Muskego, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Removed the drawer from under the stove then unscrewed the access panel in the back (two phillips head screws). Rather than take it off altogether I just swung it to one side.

The ignitor electrical connector required two hands to disconnect and it was a bit of a reach but came apart easily enough once I got hold of it.

Removed the racks and bottom from the oven. the bottom is held in by two pins in the back that you just slide toward the front then lift it out. I did not bother to remove the oven door, but some people might.

Then removed the two hex head screws holding the ignitor on and pulled the connector out of the hole leading to the bottom.

Installation is the reverse of removal The electrical connector was reluctant to back down the hole, but went with a little wiggling and pulling from underneath. Once you get it back down there the connector is keyed, so you can't get it wrong.

Piece of cake, really.

Total repair time: about 30 minutes, including the mandatory halfway beer break.

Oven wouldn't heat

  • Customer: Patricia from Buffalo, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
I removed the oven racks, the bottom of the stove and a v-shaped cover that was over the heating element. The old gas ignitor screwed off easily after I put W-D 40 on the nuts. I un ooked the old gas igniter and replaced it with the new one. The oven lit immediately after I replaced everything. I am very proud of my self, I feel like a femal Bob Villa. I almost bought a new range. Boy am I happy!

Oven slow to light

  • Customer: Dianna from Granite Falls, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 1 of 1 people found this instruction helpful
Simple... unscrew the 2 screws and unplug the electrical connection to uninstall and just the opposite to install.

Oven Wouldn't Heat

  • Customer: JANIE from DETROIT, MI
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
I first removed the screws inside the oven,let the tube that the flames come out of hang down,removed the screws from the igniter. Then I took the cover off the back of the stove and unplugged the old igniter and plugged in the new one. I put all screws back and put every thing back in place and the oven has been heating up every since. Thank you parts select. My husband is a otr trucker and won't be home until the 20th of this month. One less item on his "honey do list".

Oven stopped heating

  • Customer: JANIE from DETROIT, MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
I removed all the screws that would turn with the screw driver, and the two that were near the ignitor that were much harder for to me loosen with the pliers. I then took the back off and unplugged the old ignitor and plugged in the new one. Put everything back together, and wala!, I had a working oven again. Thank you very much Part select. My husband was very proud of me, for accomplishing it on my own, He is an over the road truck driver, and I would of had to wait until he came home on the 24th of December.
All Instructions for the CGR1420BDW
61-75 of 226