Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer would drain, but not spin
I had called a repair man; and fortunately he never returned my call. After reading many of the reviews involved with the same problem, and wanting to use my washer, I decided it was easy enough to give it a try. And so it was. 2 screws in back removed the cover; and 2 screws in the front of the washer permitted the removal of the affected part. Removed three "plugs" from old; put them on the new part; replaced it back in the washer, and replaced the two front screws, which held it in place. Replaced top, securing with the two screws. And surprise - surprise -- the washing machine was working again! Your reviews were so helpful and encouraging --- that this really old lady decided to try it --- and like they all said "It was really easy to fix."
washer stops in middle of cycle and E53 appears on the screen
1 you have to order a new motor control board 2 unscrew the back panel 3 unscrew the top panel 4 unscrew the bracket 5disconnect the old motor control board 6 connect the new motor control board
Would go into high spin in regular wash settings .
(1) Removed top of washer . (2) Open washer door . (3) Removed the two screws holding the Door Lock Sw while holding the switch from inside the machine . (4) Lifted the switch up to remove wire harness one wire at a time and reconnect to new switch . Double checked work and reinstalled switch . (5) Run washer machine make sure everything is back working . I need to add that the washer door needed to be adjusted . The bottom of the door was kicked out . Washer is now working .
By unscrew the washer Machine door off' then place the door flat surface and start to unscrewed each screw carefully keep all the screws together then remove the broken glass that you don't cut yourself in a safe place, then place the New glass back on & replaced all the screws back on tightly once all the screws back in then replaced it back on to the washer Machine, make sure you pre-test your washer Machine for no leaks.
I started by removing the two screws at the back of the washer and taking the top off of the washing machine. Than I removed the two screws securing the door lok and switch assembly. I disconected the two or three electrical connections and install the new one in the reverse order.
pulled the retaining ring then unscrewed 2 screws removed the bad switch and unplugged the old wires then hooked them back to the new switch...this was the second switch in approximately 2 years...
It was a very easy fix. Called a repairman and they wanted 350.00 to come out. Ordered the door lock and switch assembly for 76.00 and it was fixed in 15 minutes. Thank you for shipping the part so fast. Much appreciated.
For some time, our washer's door was vibrating and making noise during the spin cycles. Then after washing a large blanket, the drum stopped spinning all together. I was able to slide the top of the washer off after undoing the screws in the back and then following the directions, found that the error code was for the washer door. The drum would not spin because it thought that the door was open, confirming what we thought, the door lock and switch assembly were bad. I was able to unscrew the assembly from the front, then reach down and after ordering the new part, disconnect the 3 cables, remove the old part then redo the cables on the new assembly and Voila...working washer, woo hoo!
First unplug the machine, then remove two srews on the back of the machine for the top cover. Remove top cover and then remove two srews that hold the door locking part. Put your hand in the machine and grab the part. unplug the three wire harnessess then plug them back and put back in place and put the two srews back and then the top cover and two srews as well.
Original glass broke due to uneven load and drum struck the glass
With breakdown maual, I diassembled the door and reinstalled the glass and rehung the door and closed it. Turned on the machine and the bottom of the glass does not meet the rubber seal on the washer opening.
While using washer a E9F code appeared and stopped working.contacted parts select trouble shooting site they told me what it was ordered the part they were right on!back washing again thanks so much for the help!
Did it with no problems at all just followed the video step by step worked great done in 1hour!