CE1 - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
not enough heat to dry clothes
always unplug from outlet first, unscrewed the back off and pull off the wire from cycling thermostat ,take the two screw out that holding it in place and replace the new one .Very simple and easy. Thank you for the easy step by step video to complete this repair. James
Parts Used:
-
James C. from Cobbs Creek, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Drive motor burnt up
Instructions are available from other web sites. A few tips from me. Tape the dryer doors shut. When you remove the springs it falls open. Remember to just loosen the hex screws at the bottom of the front panel, it has slots and just lifts off of them. To easily remove the clips holding the motor bearings use a dull chisel or small pry bar on the outside half loop and tap the end with a hammer while lightly forcing it out.
Parts Used:
-
James from East Palatka, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
broken belt
this belt is too thin for the capacity of this dryer.I had only removed the front panel,replaced the belt and immediately the dryer start.
Parts Used:
-
GABRIEL from CHICAGO, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
sweaking while running
used your video instructions were great a great tool to repair. know wonder the maytag man is not busy ha ha .
Parts Used:
-
walter from fairhaven, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
I had a power serge and it burned the Plug at the termial block and melted a few wire.
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
Parts Used:
-
Robin from Vanderbilt, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Washer overflowed
Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.
Parts Used:
-
Beth from Valley Springs, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Plastic catch broke
little more than vedio showed has a see thru door had to tke door off machine then was easy replacement and re install
Parts Used:
-
Charles from North Chesterfield, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dry door latch broke
I watched the online video first, which made the removal and installation fast and easy.
Parts Used:
-
George from Melbourne, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
First squeaking, then something happened and would not run.
Removed back panel to get to inside. Removed drum etc to replace drum rollers (ordered repair kit also), replaced the idler pulley etc, now like new. Repair successful!!!! Thank you!
Parts Used:
-
Ernie from AVONDALE, AZ
-
Difficulty Level:Easy
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!