CE1 - Instructions

The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.

ordered new latch. Arrived promptly. Installed in 5 minutes. Actually easied than the video. Thanks

The Door Catch Kit had clear instructions for installation and included multiple replacement catches to fit several different sizes/varieties of dryers. I used a screwdriver to pry out the broken door catch, popped in the replacement, and was done! As usual, PartSelect had what I needed at a good price, with clear instructions for any needed installation. Fast shipping, too.

I had to take the top loose and raise it up. There are two screws in exhaust vent you have to take out then you can raise the top. When you raise the top you will have to take the front loose and open it up enough to take the drum out. Go to the back and take the lower cover off and take the screws holding the exhaust vent out so the vent will come out the top. When you take the vent out you will see a fan on the end of the motor shaft. The fan is threaded on the shaft and it is left handed threads. As you face the fan you will have to turn the fan to the right to get if off. You will need someone to hold a back up on the motor shaft inside the dryer to keep it from turning. Take the motor out then get the new motor and wire it according to instructions. Install the motor on the motor mount, put fan on then put everything back in reverse order that you took it apart. The hardest part for me was putting the clips on the motor when I put it back together. Hope this helps you.

This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin

1. Disconnect power cord and remove flexible duct. 2. Tilt dryer back and lean against wall, using folded towel to prevent wall damage. 3. Remove front/bottom panel - 4 screws on front/bottom of dryer. 4. Make alignment marks on internal vent duct where it attaches to vent bottom duct housing. Remove internal vent duct screw (towards front/top of duct) and slide vent duct out back of dryer (duct has to be removed to remove back panel) 5. Remove top panel (4 screws on back/top). 6. Remove AC power terminal block from back panel, disconnecting wire that restricts free movement of terminal block. Remove power cord from terminal block (3 nuts). Remove back panel (many screws). 7. From rear of dryer, gain access to idler pulley spring arm. Carefully note how belt routes around motor pulley and idler pulley (maybe record an image). Release belt from idler pulley. 8. Remove idler pulley triangle retainer (if still on pulley shaft) and remove old pulley. 9. Thoroughly vacuum lint and dust from all areas of dryer, internal duct, flexible duct and duct in wall (as far as possible) while dryer is in disassembled state. 10. Thoroughly clean idler pulley shaft of deposits with cloth. If desired, add very small amount of Park Tools Polylube 1000 to the cleaned shaft. 11. Install new washer, idler pulley and triangle retainer to shaft. 12. Re-route belt around pulley in original orientation. 13. Reassemble rear panel to dryer, terminal block to rear panel, and power cable and internal wire to terminal block. 14. Reassemble top cover to dryer. 15. Insert internal duct back into front vent duct, aligning guide marks, and secure with the one screw. 16. Plug unit in and briefly test, then unplug. 17. Again, tilt dryer against wall and reinstall front/bottom panel and screws. 18. Install flexible duct, plug in power cord and position unit for operation.

I read the instructions on the internet. It told me what to trouble shoot first. The switch on the door then the thermo fuse and after that the thermostat. The off on switch on the door checked ok but the thermo fuse didn't when I followed the instructions on the internet. The thermostat did check ok. When I installed the new thermo fuse the dryer started like always before. I was pretty proud of myself for saving a hundred dollars or more. Thank you for the hlpful instructions.Larry

Simply slide out old coil by lifting cooktop pan; position new coil electirc elements in oven slots, slowly push in, then push coil tab into slot in pan for balance. No problems

Unplugged dryer. Removed lint tray screws. Opened top of dryer and removed the two face screws then removed front of dryer. Released the belt tensioner. Then removed the drum. Disconnected the wiring clip and with a creseant wrench held the back of motor and turned the nut in the front clockwise to loosen the motor from the vent fan. Then simply pulled the old motor out and reversed the steps and now have a great working old dryer again.

I must say what really made this install/replacement easy is the YouTube video link that was included with the belt replacement part. Once I saw the video (which showed my exact model dryer) it was a piece of cake! There was some work involved but once I got all the screws removed and took the shell off, installing the belt was a cake walk after watching the video. Many thanks!

This worked out GREAT. We were about to purchase a new range when I found the needed parts were available. The stores we had contacted had told us our range was too old to have parts available. I had no problem with installing the receptacle at all. The pans went in easly as excepted. My wife is happy with her NEW arrangement. She does not need to learn how to operate a new range. Thanks for your help. The instructions sent were clear and easy to follow.

simply remove the burner take out the drip pan and bowl individually. Install the new one and replace the burner. no tool was used.

This is a long, sad story, but I'll cut to the chase. I was told by few appliance repair guys that my problem was most likely due to the motor being bad. I had checked the thermal fuse, the door switch, and the power switch, and all were good so that made sense. I then saw a video which made it seem fairly straight forward to remove the old motor and replace it. So I ordered the motor from Part Select. Turns out it's impossible to remove the motor without also removing (and replacing) the blower. The video never mentions that. Also FYI, I found out that my dryer switch WAS broken, and nothing was wrong with the motor, so I spent $250 on a repair that should have cost %40. Oh well ...

It snapped right in. Works perfect.

Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.