CDW9380N20SS General Electric Dishwasher - Instructions

It took all of 5 minutes to replace the wheels on the lower rack of my dishwasher. I just had to remove the old wheels and put the new ones on. I also replaced the tub gasket. This took maybe 10 minutes to push the new gasket into place.

very happy with the product and fast shipping. removed kick plate from dishwasher, inlet valve was on the front left bottom slid out dishwasher removed two screws and disconnected water line,and installed new inlet valve,very simple job if your somewhat handy,make sure you use thred sealant on water line when re installing

Repair was just a snap I used a screwdriver to push out the old wheel axle and snap the new back in. This has solved my problem of the wheels falling off, it was driving me crazy every time I used my dishwasher the wheels would off. If are having problems like me this will solve your problem.

removed front panel and replaced new part. Timer did not work because plug kept disconnecting. Called GE service and watched him remove panel without removing control panel. Plug for timer can be installed easily and front panel replaced without disturbing cable.

I took the rack out and turned it over on my kitchen counter. I then clipped on the new axles and pushed on the wheels. I wish I had found your site sooner , I can't believe how simple this was.

The quiet power 3 has the heating element in the back, so remove the screws holding the unit in place. Remove the bottom cover and disconnect the water inlet pipe, (after turning off the water of course). Discard the copper tubing if applicable, and pull dishwasher out until you can tilt it forward. Unsrew the plastic nuts and remove the wires for the element. Test the old one to make sure that you need to replace it. When sure of the problem reinstall in the reverse order. Replace the copper with stainless steel braided line and test.

Repairs do not get any easier than this. Remove 12 screws to disassemble door panel (be careful not to let front panel of assembly to drop or bend when screws release it). Remove 6 screws to remove old detergent dispenser. Unplug cable from old dispenser. Connect cable to new dispenser. Install new dispenser into door with 6 screws and then reassemble door panel with 12 screws making sure to keep all wiring free from pressure points.

Simply screwed in the new rinse aid cap to replace the old one

Took the bottom rack out and put axle and wheel on. Very simple to do. Took about 5 min. Would recommend this site to anyone. Thanks a bunch !

The rear wheel on the lower dish rack broke at the axle attachement. The wheel then feel inside the dishwasher against the heating element causing the wheel to melt. I ordered the new parts and they arrived very quickly. I attached the axle to the wheel with hand pressure, no tools required. I then attached the wheel assembly to the verticle support of the lower wash rack with hand pressure and was done. Very easy and the new design of the axle seems to attach better to the rack.

The orginal axle design was terrible. The old axles broke and fall off. The new axles snap on with moderate force but the keep the wheels on now. The Rack works perfect now!

We tried cleaning the sprayer by unclogging the spray holes but it didn't last very long. I decided to see what it would cost to replace the piece. I have used this site before and love how easy it is to find the part you need. The sites have good pictures so you feel very good that you are ordering the correct part. They also have helpful suggestions for problem.. I ordered the part and it arrived two days later and we installed it right away...I started the dishwasher for a test run and forgot how loud it use to spray..The prices are also great just a service call from a repair man would of cost me triple what I got my new part.

remove front lower cover, 2 philips screws, turn off water supply under kitchen sink to dish washer, turn off power to dish washer, remove water supply line to valve, remove power to valve, clip ons, remove two 5/16" screws holding valve on, turn valve gently to access clip holding washer supply hose, push clip up hose and hold hose while pulling valve off. re-install in reverse order, a flash light helps.

Twisted new one in place of old. Disappointed that there was a melting issue at all. Need to investigate problem.

Just removed the old rollers and clamps, replaced them with the new rollers and clamps....just that simple.