CDE820 Maytag Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Electric surface burner would only turn very hot
Well, I had to search a bit deeper in the internet to find out that the problem was not with the surface burner (which did look a bit burned out anyway) but rather with the surface burner switch (Part Number: PS336885) which must have ben damaged by the heat of the closest burner. If this problem would have been better documented (or if I would have searched more carefully) I would have saved over $40 with parts (Surface Burner Receptacle Kit) that I didn't quite need. Repairing the switch was very easy, thanks also to the available video , even though the stove used on this video (front panel) didn't quite match mine (top-back panel).
Parts Used:
-
Vittorio from Wakefield, MA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
one pole of the socket corroded to nothing
Starting by me making a substitute prong to keep the stove working while the part this coming by mail. was a piece of cake.
Parts Used:
-
martien from williamstown, MA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
It took high torque to dislodge the screws
Removed the two screws and inserted the new element. Applied a light coat of petroleum jelly to the screw threads and reinstalled.
Parts Used:
-
Jacob from Kings Mountain, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
My burners were replacements that rocked and were uneven.
I unplugged the old ones and put in the new ones.
Parts Used:
-
Janet from Goodlettsville, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Parts Used:
-
Grant from Alexandria, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Replaced worn seal
Remove the door. Place small screwdriver in each door arm to prevent extraction. Remove approx 20 screws. Remove the seal. Replace the new seal. you will need help in holding the seal in place until you car install at least two screws. Very straight forward. Took 20 minutes. Even a cave man can do it.
Parts Used:
-
Horace from Las Vegas, NV
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burner stays hot
First turn off breaker, then take screws out switch assembly,take oid switch out, put new switch on,turn power on.
Parts Used:
-
Gregory from snellville, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
very old grease filter.
Very easy to replace the filter, nothing to it, take out the old filter and put in the new filter.
Parts Used:
-
Eliane from Potomac Falls, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Simply replace the grease filter
Thanks for carrying this part for my old stove. And thanks for the great service.
Parts Used:
-
MaryAnn from Scituate, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Burned out lower electric oven element.
I simply removed all the oven racks so I could reach in, removed two screws, un-clipped the old element and clipped in the new one. Put the screws back in and popped in a chicken ready to bake. Delicious.
Parts Used:
-
Bruce from Woodstock, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door seal was worn out/burned /leaking heat
Took the oven door off hinge. Took door apart pulled off old seal from inside of the inside panel of door. Replaced with new seal.
Parts Used:
-
Christopher from Toledo, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
door wouldn't close well for 3rd time
I had repair men replace the door hinges 2times and decided the 3rd time to do it myself and save some $. ordering was a chinch, received the parts in 2 days and followed instructions posted on this site. They were excellent. Just a few things I would stress: Lift UP the door to remove, not open the door fully and pull out and also make sure to take the small pins out of the new hinges before closing. They are so small you could over look them. The person who put detailed instructions on this site is to be commended for clarity and detail on "How To" I really appreciated it.
Parts Used:
-
Barbara from Reno, NV
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burner would stay on high, on all settings.
In response to your question.......everything went perfectly!! The reason?? I read the directions that were very easy to follow. It was a quick, easy repair, and the stove burner is working like new.
Thank you for your help!!
Bob
Thank you for your help!!
Bob
Parts Used:
-
Robert from Attleboro, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Part was corroded
took out the screws replaced the cartridge top, replaced the screws
Parts Used:
-
Ronald W from Colorado Springs, CO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burners would not come on
Removed cook top top to get to wire harness and receptacle replaced and put back. This was not hard to do took about an hour. Parts came in on time and were the right parts.
Parts Used:
-
Jimmy from Valdosta, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
Was this instruction helpful to you?
Thank you for voting!