CAW2762KQ1 Whirlpool Washer - Instructions

First I removed the softener bin by pulling it up and off, then I removed the plastic seal by pulling it up and out, then I removed the 1/2 inch bolt with a ratchet and extension, then I removed the upper and lower agitator assembly from the machine and seperated the two by putting my feet on the lower agitator to hold it to the floor and pulling the upper agitator fast and firmly.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.

I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.

Disconnet the washer from supply lines. pull washer out, tip on side. Remove water hoses from pump, have to squeeze hose clamps with pliers and slide them down the hose. Then remove the hoses from the pump. Then locate spring retainers that hold pump to drive motor, place flat blade screw driver under each clip and pry clip loose, then remove pump.
Install new pump on shaft, making sure that alignment dowels line up with holes on pump. Hold pump in place and using finger push retainer clips over lip of pump, install hoses on pump, install hose clamps. Hook washer up to supply lines, drain lines, plug in and you'r done.

Replaced AGITATOR DIRECTIONAL COGS (4) looking instruction video . Replaced CLUTCH LINING KIT following video of this site "WASHER REPAIR-REPLACING THE CLUTCH ASSEMBLY". Replaced SEAL, GEARCASE COVER and NEUTRAL DRIVE ASSEMBLY as follow: 1)CLUTCH Assembly and motor removed, took the GEARCASE on a bench vise to hold in place and the long shaft up side. You can get help from other person to hold secured in place instead a vise.2)Following a youtube video I tested gearcase with a reversible drill using DIRECT DRIVE MOTOR COUPLING PART next To transmission side instead of electrical motor. Drill turning counter clockwise drive the long shaft oscillating (it agitate via agitator cogs). Drill turning clockwise run the exterior sleeved part around shaft (upper side of metal gear inside gearcase and fixed on top to clutch to get washer spin). My experience was didn't rotate so we had to take apart gearcase cover.3)Unscrewed and removed gearcase cover. Cover was sticked by old seal gasket so a screwdriver helped me to remove it.4)Cleaned joint removing old gasket.5)Repeating drill test I realized big nylon gear did'nt rotated and removed uppercut clip with pin pliers with care for not lose the pin. Removed the next washer, the plastic gear and found a plastic part with a tooth broken. This part is with NEUTRAL DRAIN ASSEMBLY so replaced assembly following part instructions. I recommend take pictures in order to reassemling and use ALLEN WRENCH 5/32'' inches.6)Fill up to half of gearcase with 16 ounces (about 1/2 of case) of gear oil supplied by PARTSELECT or automotive gear oil SAE 85w90 or SAE 90.7)Replaced SEAL, GEARCASE COVER. HARD TO REMOVED AND REPLACE! Take care not break!. I had to use a piece of metal tube and a vise.8)Applied automotrice black seal gasket silicone around the cover joint and case.9) Replaced the cover and reversal instruction video.THANKS to this site I get excellent service and Enjoyed with my toy.

Removed screws on top of machine to remove the control unit out of the way. Then used large regular screw driver to pry out the two clips that hold the back of the washer tight to the top frame. This allows the back to come away from the machine enough to get the water inlet valve free. Didn't have to remove the bolts at the bottom of the back of the machine (they were pretty rusty) Just removed the single screw holding the water inlet valve in place, slid it down and away from the back cover and could fish it out to the side and disconnect the hose (with plyers) and slide off electrical clips (make a note of which clip goes to which valve.) I removed the part first so I could make sure I was ordering the right one. When the part came (very promptly by the way) it went back together easy. Only question was regarding reinstalling the wires since I didn't mark which way they went. I knew which one went on the Hot and Cold but didn't know if it mattered which clips went on each terminal. Figuring it was AC guessed it didn't matter so put it together the way the connectors seemed to want to lie naturally. Put it together making sure no hoses or wires where pinched or rubbing against sharp edges. Replaced the rubber washers in the hoses and made sure the hose connectors turned freely (they had been rusted a bit and didn't turn on the hose freely and I think this was the start of the cross threading problem) This time the hoses went back on very easily, screwed them hand tight not forcing anything at any time (DIDN"T USE PLIERS!). Tried water and no more leaks. Washer filled faster also, think this was because the screens on the water valve were plugged. I'll have to remember to take the hoses off and make sure the screens are clear every couple years or so. If you are having slow fills, suggest you check this first before tearing in to the machine.

placed washer on side and installed new pads
and returned washer upright

pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.

Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and started stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).

3 online people recommended tilting the machine on the side and replacing the 3 suspension springs. Someone else recommended changing the tub pads. That is the wrong approach. It is actually easier to remove the case than turn the machine on the side. Once you do it once or twice it takes less than 2 minutes and it doesn't distort the suspension. You don't even have to disconnect the hoses. When I originally examined the machine lying on it's side I saw that the tub balance spring was still attached to the tub but the other end had detached. I looked for the place to reattach it. I found a place on the glide plate. Unfortunately this was the wrong place and the machine continued to bang away. When I realized that the spring had to be attached to the lower frame rather than the glide plate (one week of looking). I even wrote to the Repair guru. Once I found my mistake the repair took 5 minutes and no tools other than the phillips screwdriver to take out the 2 screws for the case. I replaced the tub balancing spring for good measure. The machine works great.

Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive assembly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.

The repair was fairly simple and while it made the spin operation quieter and and a bit more stable, it still gets out of balance. Disconnected power, shutoff supply lines and disconnected them from the unit.

Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverage with a 2 x 4 to take any residual tension off the springs.

Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors

Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.

If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.

I watched the videoand just followed your lead. It really was easy. The only thing I didn't have was the agitator grease or lube.

Remove the washer case/enclosure to expose all the internal parts. Lie on the floor and with pliers and a strong arm. Remove and replace each spring one at a time. Pretty straightforward.

After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spring bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring.
If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!

First I removed the liquid fabric softener cover, then removed the seal with my fingers, then used a socket with an extension to remove the single bolt that holds the agitator to the spindle.

Next, I pulled up to remove the agitator and tipped it upside down to take out the centrifugal mechanism. Then, I simply replaced the old parts with the new ones, and put it back together, as it shows in the included diagram. It took about fifteen minutes.

I was glad to be able to go online, and quickly locate the exact parts our machine needed, at a reasonable price! Our machine now works like new again.