CAV2005AWW Magic Chef Washer - Instructions

view video on how to remove belts, motor and water pump. I follow the instruction given. the video is very helpful, gave me all I needed to do the job myself. thanks tom

I followed the online video on the Partselect website to replace the snubber ring on my Maytag Washing Machine. It was a very good video. The video had the same exact model even. The gentleman on the video was awesome! This is my second time using Partselect for a DIY job. I fixed my dryer a few years ago by watching one of your videos and purchasing your parts. I will never call a local repair company again. Half the time the don't even show up and then they charge you an exorbitant markup on the parts, not to mention the labor costs. Of course they never have the part in stock and they always have to order it. I did call around my hometown to different places that sell appliance parts... The all said they would have to order the snubber ring ... none had it in stock. So, I bought the parts from Partselect.com, had them shipped overnight and still saved a bunch of money. After I installed the parts, my machine runs perfectly! It has been about two weeks now and it has not been out of balance a single time. I will definitely be a return customer and I will highly recommend your website to all my friends. Thank you!

The videos included in the shipping notification email made the repair a breeze. The only thing not shown was (at least on my washer) that the screws that needed to be removed had torex heads instead of normal slot or phillips heads. Luckily my tool crib had what I needed.

Disconnected in and out hoses. Unscrewed part, screwed in new, reconnected hoses, installed belt and cover panel. Stood up the machine and tested. Good to go.

Slip wire clamps over tube ends. push hose ends over connections, move clamps over hose end, making sure clamps are centered on connections. Easy as could be.

Unrolled the old one off. And rolled the new on .by pulling the driver pulley

Removed front and rear covers, replaced drive belt, tub hose and pump. simple operation. Washer still has some leakage not as bad as original leak. Think I have main tub seal problem. Going to check all hose clamps and run again. If the main seal is problem I will be forced to buy new as the parts cost and difficulty of replacement will be the important factors.

Disconnected hoses and poppped open the top of washer with a flat screw driver from the front. Removed screw holding the water inlet value with a nut driver. Diconnected wires and internal hose from the old valve and attached them to the new valve. Install new valve in place with nut driver. Clossed the top. Reconnected hoses.

First unplugged washer. Found clips on front of machine and lifted the lid back. Took out two 5/16" screws and removed the front panel. Tilted back the washer slightly and took off the drive belt underneath. Started removing the 6 springs with visegrip pliers that support the tub. Then removed the hose on the back left, no pliers needed. Then used pliers to loosen the clip holding the drain hose on the bottom of tub. Moved the clip down, then took off hose. There will be water in the hose, be ready with towel. Watched the video for snubber installation.

Lay the washer on it's side and remove the drive belt. Set back upright. Pry top cover up. Use a small flat bar and try not to damage the porceline. Two hex head screws (one on each side by the tub)holds the frone panel on. Remove those. Panel can now be tilted forward and removed. Pump is on right side. remove the two hoses and save the clamps. remove the three hex head screws holding the pump. Install the new pump and reassemble. Pretty easy.

it is best to watch the video before doing this reapir. Once you see that the job is straight forward, making sure not to remove all of the spring screws is very important.

tilted washer about 45 degrees off with old on with new belt.TOO easy

After inspecting the brake and installing the new pulley/bearing kit the washer still would only spin slowly. Discovered that if the washer agitates at all in the spin cycle then the transmission is shot. So washer was replaced with a new one.

Watch the videos on it about replacing the snubber ring. Do not remove the whole assembly just loosen enough to get old snubber out and new one in, or you will find it very difficult to get the brake/clutch assembly back together Also I used a 2 x 4 scrap to push and hold the the barrel while removing the six springs. Wear long sleeves as the metal on the washing machine panels will cut you very easily. Belt was just sliding it over the pulley. One other recommendation is take a pictures before and while you are taking it apart for verification of reassembly.

Followed your excellent video instructions to change out the motor.