Models > CAV1004AWW > Instructions

CAV1004AWW Magic Chef Washer - Instructions

All installation instructions for CAV1004AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CAV1004AWW
61-75 of 337
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer made a loud noise during spin-eventually stopped spinning

  • Customer: Christopher from Haverhill MA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Socket set
  • 5 of 5 people found this instruction helpful
I was able to get the belt off easily but the belt was fine. I changed the snubber easily also. But that wasn't the problem. I went through all the parts that are easy enough to change without a mechanic but turned out it was something inside the innerbasket and we had to junk the washer and it was only 4 yrs old.

WASHER SHAKES AND DANCES

  • Customer: Adrian from West New York NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Wrench set
  • 6 of 8 people found this instruction helpful
NO NEED TO BUY A BRAKE WRENCH NOR THE EXPENSIVE SPRING REMOVER.
ONCE THE DRUM IS OUT THE WASHER TURN IT UPSIDE DOWN AND LOOSE THE SCREWS HOLDING THE TRANSMISSION ABOUT A LITTLE MORE THAN HALF WAY, TO GIVE THE NEW SNUBBER ENOUGH ROOM TO FIT IN, THEM TIGH AND ASSAMBLE EVERYTHING BACK TOGETHER

both hinges on washer lid were broken

  • Customer: Harris from Ashland PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
if you move the agiatater all the way to one side you can acess the star screws from under the hinge then push the agitator to the other side and acess the screw on the other hinge , you dont have to remove the top of the washer, let me say i did not have the serial no and the people at part select were very helpful and pacient when i called and they got me the RIGHT part the firdt time.thanks again for all your help the job came out perfect and saved me a lot of money for a repair man. ASHER

Water Pump Failed

  • Customer: Douglas from State College PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Wrench set, Wrench(Adjustable)
  • 7 of 11 people found this instruction helpful
Obvious problem: belt destroyed. The plastic pulley on the motor was damaged beyond repair. Since you can't replace just the plastic pulley, you have to purchase another motor. The machine still would not spin. Checked the pump again. The bearings might be bad. Replaced pump; Success! washer works again. Total repair: belt $15.68, new pulley with motor $132.00, and new pump $80.00. Estimated cost to repair about $228.00. Time to troubleshoot. 1 hour, time to fix 1 hour; Total time in labor about 2 hours.

Washer went off balance and the flume broke off

  • Customer: Michelle from Jupiter FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 18 people found this instruction helpful
I removed the part that was still attached to the washer and installed the new flume. It took less than five minutes and a repair that would have cost over $85 cost less than $10 and I am no plumber!

MAKING NOISE DURING WASH CYCLE

  • Customer: MARK from HEBRON KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 8 of 15 people found this instruction helpful
REMOVED EXCESS WATER,REMOVED HOSES,TIPED BACK WASHER,REMOVED BELT,REMOVED PULLEY AND BEARING.REMOVED 3 SCREWS AND REPLACED WITH 3 LONGER SCREWS IN THE STATOR,THEN REMOVED 3 SHORTER SCREWS.THEN LOOSEN VERY SLOWLY EACH OF LONGER SCREWS TO RELIEVE PRESSURE FROM THE BRAKE SPRING.ONCE LOOSE,PULLED OUT BRAKE ROTOR.REPLACED WITH NEW PARTS.WORKS LIKE NEW.

Water intermittently leaking from bottom of washer

  • Customer: Debbie from Colchester CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers
  • 5 of 6 people found this instruction helpful
I could not tell where the leak was coming from. It was intermittent. Also the clothes were not getting totally dry in the spin cycle. Finally the drum stopped turning. The bearing in the waterpump was shot and the water was leaking from the waterpump. Luckily or unluckily, the bearing completely went and I then found out that the intermittent leaking was coming from the pump. I replaced the pump and the belt that was damaged when the pump bearing locked up. This has resolved the leaking issue.

Topside door would not remain in an open position; lid hinges worn out.

  • Customer: James from Oakland MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
The lid hinges are fastened to the top of the washing machine body, near the edge of the lid, with 1 screw each.
To remove the old lid hinges, with the lid clamped in the open position, I needed to gain access to the screw heads from underneath, just inside the edge of the lid opening. To get at these screw heads, I needed to push the inside wash drum toward the screw I wanted to remove and wedge something in the gap created between the body of the washer opening and the drum, directly opposite the screw that I pushed the drum towards. What? This is to hold the drum completely out of the way while getting at the screw. My wedge was the handle of a squeege that just happenned to be nearby, but just about anything will work.
Once the drum was secure, I was able to get at the screw head, which, by the way, is a totally blind operation; you cannot see the screw head, only feel it. I guess we're kind of used to feeling our way around these days. Anyway, I had to repeat the wedging thing to remove the other lid hinge.
The only real problem I had was the original (factory installed) screw heads were hex heads, and I struggled a bit finding the correct size allen wrench to blindly remove the screws. It is a good thing that I also ordered 2 new screws along with the new lid hinges because the new screws have phillips heads. Much easier to work with, even though they were a little pricey. The old hex head screws were kind of worn and it would have been a cursing operation to try to reuse them.
Once the old hinges were off, I removed the lid, installed the new hinges on the lid and clamped the lid in place in the open position, while I screwed the new hinges on (wedging the drum out of the way like before). NOTE: It might be a good idea to line the wash drum with newspaper in case a screw slips out and finds its way into one the holes in the drum; lost forever. Anyway, this may sound like alot, but it really isn't. My wife didn't even comment on how the lid isn't smashing down on her any more. That's OK, I'm grateful I'm not the one doing laundry!

Agitator had broken fin

  • Customer: Floyd from Davidsville PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 5 of 7 people found this instruction helpful
Popped off bleach cap on top then got socket and long extension removed bolt, cleaned a little then replaced new agitater top.Replaced bleach cap and i was done.

Broken agitator caused intermittent shutoff

  • Customer: Tai from Lenexa KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 6 of 10 people found this instruction helpful
1. Pulled top off (liquid softener dispenser section)
2. Put 2 socket extension and a 13 mm socket together with socket wrench (tool).
3. Insert tool with 13mm socket end into old agitator and unscrew bolt.
4. Remove tool and then remove old agitator.
5. Turn old agitator upside down to remove bolt.
6. Insert new agitator where old agitator was in washer.
7. Insert bolt.
8. Insert tool with 13mm socket end into old agitator and screw in bolt.
9. Pop top back on.

Hardest part was finding extensions because one wouldn't reach.

new belt worn out by a bad motor pulley

  • Customer: ALBERT from WASCO CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 5 of 7 people found this instruction helpful
i took off the old belt and i took off the motor pulley with the pliers and srewdriver. i put the new pulley in with my hand and gave it a hit with the palm until it snap in and then i put the belt on by rotating the main pulley on tub till the belt was pulley on.

Leaking Water Pump

  • Customer: Edwin from Eagar, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 4 of 4 people found this instruction helpful
Pulled wahser away from wall, unpluged, removed screws from rear access panel, removed hoses from water pump, used towell to absorb excess water still in pump and hoses, removed drive belt, removed screws securing pump, removed old pump replaced it with new pump, cussed a little when replacing hoses, repeated steps in reverse order, checked for leaks.

Water would not shut off after filling desired level

  • Customer: Richard from Geneva OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 7 people found this instruction helpful
Took out the two top screws out that hold the top down on the back so you can lift the lid up. Removed the cover plate on the back. Take out the screw that holds the valve in place. Reach up through the access panel and undo the to clips that hold the hose and wiring. Lift the lid up and pull the unit up and remove hose and electrical connections and put back in reverse order. Very simple to do.

water kept filling until overflow

  • Customer: Michael from Woodside CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 10 people found this instruction helpful
removed back of control panel to find that a mouse chewed the air tube. tried to splice it with a barb connector, it did not work. Ordered part received it 2 days later and installed it. I would recommend buying parts from these folks!

White fluffy residue appeared under washer. Unbalanced banging during spin cycle

  • Customer: John from Blue Bell PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to remove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.
All Instructions for the CAV1004AWW
61-75 of 337