Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Noisy refrigerator.
Remove the 4 screws holding the back cover onto the refrigerator. Unplug the power for the refrigerator. There's 3 bolts holding the fan motor assembly to the refrigerator. Loosen the two bolts which allow the brackets to pivot out , and remove the third bolt. Disconnect the electrical leads, and remove the fan blade, then rotate the fan motor assembly out from the refrigerator. Install mounting brackets from the old motor onto the new motor, then reinstall the assembly in the reverse order of removal.
Original evaporator fan (31 years old) was making a lot of worn bearing noise
Empty freezer; Remove shelves and ice trays; Unscrew and remove the rear vertical panel; Unscrew and remove fan housing; Unscrew and remove fan from fan housing; Fan blade slides off the motor shaft without tools. Reverse order to reassemble with new fan motor.
I did have to use the wire extensions that were included as the replacement motor had the electric connections in a different location from the original motor.
freezer too cold and refrigerator not cold enough because fan not working
Had to defrost a bit and then was able to remove rear freezer panel by simply removing the 2 screws holding it in place. Old motor easily removed from its mounting bracket. and replaced with the new. Had to use the two wires sent with the motor. I clipped off the male connectors and joined them with wire splicers to the black and red wires clipped from the old motor. Then reinstalled. The replacement motor works great. I was afraid the old fan blade might not fit but it slid on perfectly.
Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple
I removed the back of the refrigerator access panel disconnecte the 3 bolst holding the motor to the fan shroud assembly and removed the burned wires from the recepticle end at the wring harness. The fan motor comes with wire nuts but I chose to use the same style of connector as came with the OEM motor. I purchased the new connectors from NAPA and they are an exact fit. The new motor fit perfectly and has run flawlessly since the installation. It is in an awkward location and that takes time to get yourself into position but once there the assembly is very simple and it is rewarding to be able to use the appliance again. The ordering from the website and phone order are very easy to do and you have what you need in a timely and expeditious manner.
The motor was making a thumping out of balance sound.
Naturally you have to push the frig from the wall and unplug it form the wall outlet and while you are removing and installing the old motor and installing the new motor. Do not open any of the frig and freezer door untill you are finished and you plug the power cord back into the wall outlet. Remove the lower back panel with a screw driver or a 5/16th hex driver. It is a kind of carboard. Once all the screws are out of that panel pull the top out from behind the steel above and then pull it out from the bottom and set it aside. Unplug the power line off of the motor. There are 3 separate brakets holding the motor in place. 1st remove the fan from the motor by romving the finger nut off the motor shaft and then remove the 1st bracket screw from the bracket all the way. Then use a light to see the other 2 screws and you will see that you do not have to take them all the way out like the first one. Just loosen the other 2 and then turn the motor and brackets counter clockwise and then pull the motor and brackets all out as one from the right hand side of where the brackets were mounted. I took the motor and brackets to the counter and removed te brackets from the motor and installed them to the new motor making sure that the bracket with the one screw hole in it is mounted at the right place so that when you reenstall the motor and brackets will let the motor wire connector be the closest to the outside where you can replug the power cord back onto the motor. Install the fan onto the new motor with the new finger nut that comes with the new motor. replace the back panel and pkug in the power cord fot the frig and let it run. Mine ran a lot quieter after the new motor was plugged in. Have fun if you have to do it. It is worth it.
Compressor fan bearing worn. Refrigerator was manufactured 9/78/
I followed the instructions verbatim as others explained. I did it step by step exactly as instructed, The timing was almost exact no more than 30 minutes. I removed the fan the night before the delivery of the new fan and used a small desk fan to cool the compressor. It worked fine in one half hour my freezer read a perfect zero. Thanks for all the help
Removed floor grate,romoved screw holding timer,push timer back,removed hex-screw holding bracket,removed ground wire.Removed connectors from old timer and put on new timer,pushed back new timer,mounted bracket,screwed new timer to bracket. Set timer to defrost at 11pm,put back floor grate.
