BJLR473GT0WW Dryer - Instructions

Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.

I received the replacement part I ordered from PartSelect.com within 3 days of placing the order. I opened the plastic bag it came in. I snapped the part into the holes left vacant by aforementioned abscence of broken part.

Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front cover screws. Piece of Cake!

Remove old one, put the new one in!

After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.

Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.

Unscrewed 4 screws,pulled off front of machine.Unscrewed 2 screws holding coils on,unplugged coils,installed new coils,plugged in coils,reinstalled 2 screws for hold down brace.Reinstalled front cover,plugged dryer into outlet(remember to unplugged dryer before working on it).started up,instant heat,works great.thanks Partselect for helping me out!!!

I first throwed the breaker then I took the old bulb out. Put new bulb in. Turned the breaker back on.
It worked great

I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.

The repair, from the time that the bulb burned out until it was replaced took about six months. I could have shortened the time if I had ordered the bulb sooner. It was difficult because I had to listen to a fair amount of nagging, which, thankfully, has now ceased. I also had to actually go online and finI opened the dryer door, reached in with my right hand (which happened to be holding the new bulb) and screwed the new bulb in. Tip: Screw it in counter-clock wise. This was not mentioned in the instructions. Come to think of it, no instructions were provided. The company might wish to correct that oversight.

Removed the broken handle from the dryer and popped on the new one.

my two twin boys Mike and Curtis age 14 did the repare they toke of the front of the dryer then the top put the belt around the drum then put the top and front back on then went to the back and removed the panel and put the belt on the pulley then set the tension wheel then put the back cover back on
the repair was easy I watched to make sure they did it right and did not have to tell them how I am very proud of them they do great work
finding the part was easy and it was here the next day after I ordered it and it was only sent 3 to 5 work days. You guys have a great web site and fast shipping thanks for the good work!

I just pressed the latch with my thumb, the latch went in, and voila....job done. Thank you

I opened the vent system (screwdrivers to loosen screws) and used the shopvac hose and my hands to clean out what I could. I also snaked the shopvac hose down into the dryer and removed clogged lint. Then I just replaced the lint filter.

Easy as 1-2-3. I took off the top hinge screws in order to lift up the top of the dryer.

I then took off the front dryer piece with the door intact. The lint filter was in the front door section.

I released the wiring clips to the front of the dryer and lowered the front of the dryer down gently. there is enough slack with the wiring if you disconnect the wirre clips.

I removed the old broken belt. ThenI gently lifted thr dryer drum enough to slid in the new belt with the ridges down. Look for the old belt line (worn area on the drum) and slip the belt up on the drum to that point.

Then I replaced the wiring with clips and put the front of the dryer back together.

Going around to the lower back of the dryer, I unscrewed the back plate where the exhaust comes out. It was 8 screws with a socket.

Once the back was off, I pulled the dryer pully to the right and fed the reamider of the belt through both pulleys ensuring that the ridged side was on the correct side of the pulley. The pylleys match the ridges on the belt. I rleased the tension on the movavle pulley and it was done.

All I had to do was button the back up and do a "dry run" I quick have the drum a half roation from inside the drum with the door open. Then it was all gravy. I was done and saved myself a good deal of money. Look on the net for pics to make thing easier for you. There are people out ther who will NOT charge you for this info.

Getting to any of the parts in the Maytag dryer is easy. Tip the dryer back and slide a 4 x 4 block under the front edge. You remove the whole front panel after you remove two screws at the bottom corners of the front panel. You need to tip the dryer back to get a screwdriver on the screws. Swing the front panel up to release the top of the door panel from the top. Watch the short wires to the door switch. Unhook the door switch wires and move the front panel out of the way. The timer on the top is accessed by re-moving two screws along the top edge. There are four screws. Remove them all and tip the top of the front panel forward. You then see that two screws hold the panel and the other two screws just hold the trim.

The dryer started normal. The drum motor run when the start button was operated. The fluff cycle operated normal to indicate the timer motor was OK. On the dry cycles, the igniter heated up. The gas came on. The dryer run for some period of time and then the flame went off. The thought was that the low temp cycle thermostat sensed the dryer was hot and thus switched over to time the cycle to its end. However, the low temp cycle thermostat tested good with a meter when the sensor was removed from the dryer and heated with a light bulb. Burnt contacts in the sensor were a possible problem. I also though the radiant sensor may be bad and not recycling after it got hot. After time, the igniter would cycle on but the gas flame would not come on. I thought the radiant heater might not be tripping the secondary coil on the gas valve. The gas valve coils tested good. I was checking them cold after the dryer had cooled down. I ordered a number of parts.

I got lucky and did a test on the coils while the dryer was still hot. One of the coils in the dual booster holding coil was going open when hot. When cold it had enough continuity to let the gas valve cycle on once. After the coil got warm it went open and shut the gas valve off. When the coil did cool off, it again had continuity. I was about ready to trash the dryer when I finely found the problem. I am happy I persisted and worked the problem through to a solution. I purchased several extra sensors but saved money in the long-run. I rate this problem at the high end of complexity for the do-it your self home owner to solve. The problem was an easy fix once the real problem was found. Only 4 screws and 3 push on wire connectors (two were on the front panel for the door switch).