Quick Question!

Have you ever purchased from PartSelect.com before?

Models > BGHD2433KW0 > Instructions

BGHD2433KW0 Frigidaire Dishwasher - Instructions

All installation instructions for BGHD2433KW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the BGHD2433KW0
1-15 of 314
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The spray arm would fall off during the washing cycle.

  • Customer: Roy from Worcester, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 623 of 630 people found this instruction helpful
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.

Leak in the water inlet valve/solinoid

  • Customer: Mickey from Ooltewah, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 132 of 144 people found this instruction helpful
1. Shut off water supply.
2. Removed inlet water hose where it connects to the vavle assembly.
3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection from the solinoid.
4. Removed the inlet hose adapter connection from old valve and installed into new valve.
5. Attached electrical connection to new valve solinoid.
6. Remounted assembly to the frame.
7. Re-attached the inlet water hose to the hose adapter connection on the valve.
8. Turned on the water, washed some dishes.

dishwasher was leaking water

  • Customer: Charles from Milton, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 112 of 129 people found this instruction helpful
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.

Upper spray arm had been "blowing off" during wash cycle.

  • Customer: Mary from Alexandria, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 66 of 76 people found this instruction helpful
Unscrewed retaining ring, replaced unit = piece of cake

Leaking under door

  • Customer: Ronald from Berwick, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 65 of 79 people found this instruction helpful
Received the part 3 working days after order. Part was exactly like the original.
Removed the door. Slipped off old gasket and replaced with new gasket. Replaced door and tried rinse cycle. Worked perfectly.

Water leaking under the dishwasher

  • Customer: Dennis from Tryon, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench (Adjustable)
  • 58 of 61 people found this instruction helpful
I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwasher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.

upper spray arm retainer nut failed

  • Customer: Michael from Hillsdale, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 35 of 36 people found this instruction helpful
simple repair..woke up one morning and after the dishwasher cycled, I noticed the upper spray arm laying on the top tray.
ordered new one from site, was delivered with-in 2 days ( with standard shipping) all 1 piece, took seriously 5 seconds to unscrew by hand and replace!

replaced dishwasher motor

  • Customer: John from Herndon, VA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 38 of 57 people found this instruction helpful
Single-handedly. Tipped dishwasher on its side for easy access to water and electric connections. Went back together with no problems or leaks, washes quiter than ever.

No water to dishwasher on any cycle

  • Customer: David from Las Cruces, NM
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable)
  • 29 of 35 people found this instruction helpful
Unplugged dishwasher, pulled it out. Unclamped hose and unscrewed water source to inlet valve, removed wiring harness, unscrewed bracket and reinstalled new valve. Now have a functioning dishwasher.

Dishwasher door was leaking water at the bottom corners.

  • Customer: David from Saint Michael, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 26 of 32 people found this instruction helpful
It took less than a minute to remove the old bottom door gasket - it pulls right out. You wouldn't think the part looks the way it does (a 1.5 inch wide plastic strip that runs the length of the door with rubber gaskets on both ends) but have faith. Trust the diagram/picture - it is the correct part and will fix the leak. The new gasket arrived within a couple days of ordering and was simple to install - no tools. It slides into place in less than a minute and is held in by friction. Problem solved and no more leaks. For under $12 (parts and shipping) I had my dishwasher fixed. A service call by itself would have run $75 - just for someone to show up at the house, and then probably another $50 for parts and labor to install. My wife made the comment "Even I could have fixed that". A very simple and easy repair - you can do it!!!

Drain hose was missing

  • Customer: John from Carthage, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 24 of 28 people found this instruction helpful
My friend bought a used dishwasher at a garage sale, the previous owner had thrown away the drain hose because it was "nasty" they said....remember it could have been cleaned. When I went to install it, I removed the old washer, and discovered that the old hose would not fit on the replacement dishwasher. I went to the local repair shop, armed with the model and serial #'s. they searched and searched their books and could not find the hose part number. they said "good luck" when I left...I went home and looked up the model on your web site, ordered the hose, and in 3 days had the dishwasher installed and running in about 30 minutes...thanks for prompt shipping.. I couldn't believe it arrived so soon...Mowerman

old valve leaked

  • Customer: Ron from Billings, MT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable), Wrench set
  • 23 of 26 people found this instruction helpful
I will make a few additions to the other instructions, which are great and let me see that the job was doable. To the tools needed, add pipe tape.
1. Shut off water supply.
2. Removed inlet water hose where it connects to the valve assembly. (This was a pain on my machine—too little room for the wrench, you may have a better tool—but I did get it out, slowly.)
3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection (Look for your red and blue wires on the connector, my red was to the top of the solenoid, and reattach with the same grounding) from the solenoid. (This step was a great bit of information; It allowed me to see that I could do the following steps with ease, That is, the unit dropped down where you could work on it.)
4. Removed the inlet hose adapter connection from old valve and installed into new valve.
5. Attached electrical connection to new valve solenoid.
6. Remounted assembly to the frame.
7. Re-attached the inlet water hose to the hose adapter connection on the valve. (I had to take off the L shaped connector at the bottom of the old valve and add it to the new valve. This was an extra step that required two bigger wrenches to hold the old assembly and unscrew the L joint. I just needed the extra leverage to get the old off and the new on. I am referring to the copper connection that connects to you water supply)
(8) The new valve had a slightly different configuration than my old. The rack it sits on was about an inch or so longer. This meant that I had to readjust my copper pipe just a bit to match up when it was reassembled. No big deal, I had lots of pipe length to work with. Actually, moving the valve a bit further back made more room for the wrench to work—very happy about that. In addition, the hose attachment went from a left exit to a back exit. Doesn’t seem to matter.
(9) Turned on the water, washed some dishes. (Took me about an hour, mostly because of the difficulty with the wrenches. Otherwise—piece of cake)

Heating element corroded, not heating

  • Customer: Denise from Burnt Hills, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 22 of 25 people found this instruction helpful
Removed bottom plate and heating element brass nuts. Disconnected heating element. Connected new one then replaced brass nuts. Put bottom plate back on. Very easy.

Dispenser door broken.

  • Customer: C from Covina, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 22 of 31 people found this instruction helpful
Disconnect from power
Unscrewed 4 phillips screws from top of outer door.
Unscrewed 2 screws each siide of door.
Lower outer door section drops away.
Note wiring sequence on dispenser, then disconnect wires.
Unscrew 6 screws on dispenser and lift dispenser out.

Place new dispenser in place (note orientation), ann fasten in place with screws, remembering to replace wire retainer on left lower screw.
Reconnect wires to dispenser correctly.
Slide lower outer door over tabs and secure with the 4 side screws.
Ensure lower door is up under control panel and secure with the 4 top screws.

Fill dispenser with detergent, reconnect power and test run while enjoying a cup of tea in celebration of a job well done..

No water to dish washer

  • Customer: steve from virginia beach, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 28 of 50 people found this instruction helpful
After figuring out the problem wasn't the water inlet switch, I replaced the switch assembly for the water level float. Cut off supply water to dishwasher, removed the 2 screws holding switch assembly, and installed new switch. 15 minutes, very easy job.
All Instructions for the BGHD2433KW0
1-15 of 314