BDNT22L9K Refrigerator - Instructions

I started by changing the water inlet valve. It made one batch but it did not eject into the ben. I removed the ice maker and found that the coating inside was bad. I changed out the ice maker and it is now making lots of ice.

Reomove Ice bin from unit.remove plastic front. Remove the 2 bottom screws of dispenser assembly. removed old assembly. position new assembly. Replace bottom 2 screws.reinstall plastic front and reinstall into unit.

I went on line and viewed the video. It looked so easy I ordered the new ice maker. Having the information I was able to take apart the old one and view the problem. By the time the new part arrived I was experienced with the installation. I was shocked when the new ice maker arrived within 1 day. I completed the installation without a hitch, I was delighted with the ease of installation and the operation of the new iace maker.Thanks again...Ray

I removed contents of freezer as this was a bottom unit. I had to remove freezer drawers/door to easily access ice maker which was located in the back of unit,wasnt a problem.I did however take a hair dryer to water tube as it froze up with about an 6 inch tube of ice that finally slid down. Connected unit and had ice within an hour or so and a full tray within 24 hrs. Second ice maker in little over a year...Video very helpful, saved 100 bucks by doing myself. Part arrived fast, great job!

We ordered a PartSelect PS2121513 ice maker. I was concerned that there was no instructions shipped with the unit. Fortunately, PartSelect had an online video that guided me through the process. It wasn't that complex really. The only time I felt totally dumb was when using my nut driver to remove the bottom bracket. I couldn't figure out why there was no 1/4" socket with my set, so I used a small socket wrench instead. I finally figured out that the driver was already a 1/4", without a socket in it. After that it was easy. Slid the ice maker up a little to free it from the top mounting screws. Pulled it outward a bit to gain access to the connector at the back of the freezer, then squeezed the two sides of the connector and out it came. I popped the plastic cover off the existing device and then removed the connector as instructed in the video. I also removed the bale (as per the video). I put the connector harness, plastic cover and bale on the new ice maker and put it back in, this time using the nut driver on the bottom bracket :-). My only concern after that was that it didn't seem to be working. I had no idea that it needed some time to get cold before it would work. After about an hour, it filled with water and began making ice. Success.

Easy repair - Don't over complicate it. 1) Flip up ice bar to stop making new ice. 2) Pull out the complete ice bin/tray. 3) shut freezer door while you work on the ice bin. 4) All you need to do is remove the 4 screws holding the ice bin holding tray to the front of the Ice cutting section in the front. 5) Screw drive can then be pulled forward to remove the old/broken white drive cap. Just replace the White Drive ring, put the drive screw back into the ice bin tray and re-install the 4 screws. 6) When re-inserting the bin, you may have to twist the screw drive slightly to re-align with the motor bracket in the back of the freezer. Suggestion: throw out old ice because if it is wet or slightly melted, when you put it back in the freezer the ice will freeze/clump together into a large ice clump; not cubes. Also dry out the ice bin so there is no water to freeze up or create a new jam when the ice bin now re-freezes.

turned off the water supply,disconnected the power from icemaker to the back wall,loosened the two screws on the top,and one screw on the bottom.removed old icemaker.took the bale off,to put on the new icemaker.removed the wire harness from the old,to put on the new icemaker..saved over $200 for the repairman,had a full tray of ice in 6 hours.(watching the video,helped)!!!!!,very thankful for your service,as most of my appliances are all in that ten year period,i will be ordering more as needed.

Pull out plastic cover #13of refrigerator part discription (temp. control and light socket), snap out old light socket and replaced with new light socket. light is now working.

Empty out freezer loosen two top screws and took out bottom screw. Lifted out ice maker and unplugged wire. Took bailing arm and plug and put on new ice maker and reverse the process. Had ice in three hours and no leaks.

Removed wiring from old ice maker and install on new. With 2 screws all ready in place hung ice maker on them. Attach wire connector into socket and install bottom screw to hold ice maker. Tighten top 2 screw and put wire guide in place. Drop wire guide down and ice started in 10 mins

I wasn't sure about the part I needed so I called the service number, they help me decide on the correct parts for my unit. This was the easiest repair I've ever done. One hex head screw and one clip in electrical connection and we were done. It took less than 5 minutes and now it works like new, no more leaking water and plenty of ice.

Removed the old fan; cut the wire and spliced in the new fan and reassembled. A little over one hour. Refrig is working perfectly now with lower settings. It is definitely off much more than on now.

I simply followed the online instructions. Easiest repair job I have done. Once installed, which took about ten minutes, it was producing ice in less than two hours and is performing as it should. Had my frig not been a bottom freezer the installation would have taken less than five minutes. And to let everyone know, the on line instructions came in very handy during the removal process. Many thanks.

I ordered the replacement parts on line and received it a few days later. Thought I'd wait till the weekend to install the new parts. I expected it to take longer so I waited. Boy was I wrong. The hardest part was unloading the top shelf of the freezer. And it took longer to go get the nutdriver. I should have put it in immediately. Thanks for the instructional video. Works like a dream NO LEAKS. Will use your services on other parts as needed. Don from Pittsubrgh, PA.

Followed video advice