Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Stove top element not working due to bad receptacle.
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit. My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts. The element is working great now. Whenever I need appliance parts again I'll use partselect.com.
Burner was out but the burner coil worked on onother burner
Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.
Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.
Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.
Stove top wouldn't come on. Oven couldn't go higher than low heat
Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00 Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine. Thank you, Thank you Part Select for your help and honesty.
The oven and ranges would not heat up and an F9 error was displaying on the Oven Screen.
So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Before I give procedure steps, please note the following observations that I had. a)If AC power is plugged in and an electrical terminal touches the frame, the resulting arc may require that you reset the GFCI or the circuit breaker. b)The clock failed to run until it was properly mounted (including the back cover in place). c)Movement of wires can cause them to work loose at EITHER end of the wire. d)Attempting to operate the clock, Start and Stop knobs may extremely difficult or otherwise ineffective unless it is properly mounted. Fully depressing these knobs / shafts is difficult.
The numbered steps below are how I would do it correctly based on what i learned. 1)I unplugged gas range power cord. 2)Re-positioned range to access the back without damaging the flexible gas supply line. 3)Removed the rear cover (#2 Philips) behind the timer. 4)Verified no voltages present 5)Judged that the front cover glass needed removal - removed timer knobs and front glass cover 6)Removed existing clock timer by using a WIDE flat blade screwdriver to depress the rear of each clip and pushing the time our the front. Old part has damaged gears and one axle end out of position. 7)Fed old timer back through the opening to the rear to assist with transfer of wires. 8)With the assistance of a helper, transferred the wires one at a time from the old to the new timer. 9)Fed new timer back through the opening to the front; aligned and snapped into place. 10)Replaced front glass and knobs. 11)Plugged in AC cord (first did inspection for snug connections and potential shorts). 12)Tested buzzer feature of the timer. Unexpected that the buzzer was intermittent. 13)Unplugged power cord. Found & tightened loose connection - not at timer but other end of one of the timer wires at the chassis connection strip. 14)Reinstalled the metal back cover & plugged in the AC cord. 15)Set the timer start and stop times to one hour before present time. (Knobs need to be depressed.) 16)Set clock to present time by depressing the knob IN and rotating it clockwise to the correct time. As clock is manually advanced to the timer start and stop times, verified that each knob popped out. The hand on the clock for the timer moves also, but when you release the knob pressure, the knob pops out and then you set the timer past the buzzing to zero. 18)I put the oven through a self-cleaning cycle. This uses the new timer; starts when the START button pups out and stops when the STOP button pops out. Of course there are other controls you need to manipulate for the self-cleaning cycle i.e. CLEAN settings and the door lock.
Changing the socket with a new one simply required removing one screw and splicing the two existing wires to the pigtails on the new socket. It took longer to unpack the replacement part than actually doing the job.
First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!