ATB1910DRW Admiral Refrigerator - Instructions

Cubes in bin were freezing together due to water leaking from the ice maker assembly. Replacement went easy with bin rails removed.

1. removed bottom screw. 2. pinched sides of rear connection to disconnected ice maker (noted red wire on top in cabinet rear). 3. bump out old unit taping to release tab on bottom. 4. disconnect wire from icemaker and remove wire holder with philips screwdriver.ew ice maker. 4. reattach harness to new ice make and replace clip. 6 reattach l bracket to bottom of ice maker. 7. detach shut off wire from old ice maker and replace on the new maker. 8. place back into position in freezer compartment. 9. reattach water delivery tube 10. connect wire to rear of cabinet. If motor drive still good on old maker scavenge before throwing away bad parts.

empty frezzer take door off unplug wires going to ice maker unscrew/bolt icemaker replace door take motor cover off ice maker remove screws on motor replace ice cup and put every thing back together

We were not hearing the water turning on to fill the icemaker tray. Took a chance it was the inlet valve. We were right. Removed old one, found on the lower back side of the frig. Unplugged electric supply, plugged new one in and refastened. In 5 minutes we were hearing the water turn on to fill the tray! Thanks

I unplugged the refrigerator. Then removed the ice tray. Then removed the screw holding the ice maker secure. I had a little difficulty lifting the ice maker off the clips on the side of the refrigerator but was successful. Then unplugged the wire harness from the back of the refrigerator an lifted the unit out. Removed the wiring harness from the old unit and installed it on the new one. Then positioned the new unit so I could plug the harness in the refrigerator and lined up the clips to attach it on the side of the refrigerator, being careful to line up the water distribution tube. Replaced the screw to secure the ice maker and plugged the refrigerator back in and it is working very well. I am very hsappy with the repair

Video was helpful and reading the other responses online was a big help also. Followed all of those instructions. Most difficult part was disconnecting the electrical plug to the ice maker. Need a screwdrive or other pointed object to depress plastic tab. Other than that, things went smoothly. HOWEVER, after turning water back on and plugging in fridge, I thought everthing was perfect...no leaks initially. BUT, came back a few hours later to find no ice cubes in the holding tray, "iceburg" formations and ice dams built up again thoughout the freezer. Water was leaking continuously from the ice maker. Upon further analysis, it appears the electronic mechanism keeps telling the fridge to send water to the ice maker...or, it is sending too much before shutting the water off. The tray is overflowing and that seems to be the problem. I'm back to square one, but with a new ice maker.

Quickly after video

Watched the video on the web site and then followed the instructions. It was very easy to change. After changing it, I filled it with water from a cup to get it started making ice since the video does not address how to do this. It has been working well ever since. If you are handy with tools, you can do this.

I put in a new ice maker because it was not in very good condition. The water valve had a very slow leak which allowed water to freeze on the way to the ice maker and plugged the line. This problem was in one of your repair articles all of which were very welcome

I had to replace the whole unit. The tray should have lasted longer and there should have been a replacement tray available.The installation was easy. 3 screws removed, unplug unit, turn off water and put in new unit.

Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.

Removed the freezer door and replaced with the new hinge.

I turned off the water and electricity to the refrigerator. Then I removed the ice bin exposing the ice maker. I loosened the two screws on the wall with a 1/4" nutdriver and I removed the horizontal screw on the bottom of the ice maker again with the nut driver. That allowed me to lift off the ice maker so that I could remove the wiring harness from the ice maker. A flat screwdriver helped me push in the retaining tab, and disengage the harness. Installation was in the reverse order. A third hand would have helped reconnect the wiring harness, but I put a shoe box on the top shelf of the freezer compartment to hold the new unit while I connected the wiring harness, making sure to "hear it click" when fully engaged. I then removed the wire "feeler" from the old unit and inserted it in the new one. Inserting the water inlet hose and hanging the ice maker was simple after that. The existing bracket holding the ice maker on the bottom was not rusted so I did not replace it even though a new one came with the ice maker. I should add that I had previously defrosted the freezer in order to remove the ice bin as it could not be removed with the block of ice that had frozen in the front end. I'm a senior citizen with no prior experience in changing an ice maker. I wasn't trying to set an amount of time it could take which was about 40 minutes, including the time it took to turn off/on the water and electric breaker and go to the garage for a flat screwdriver and find the right size nutdriver, and next time I could probably do the job in about 20 to 30 minutes! Bob I. San Diego, CA

Removed bad motor with socket set and pliers then removed the connectors from the old motor and soldered them on the new one. Then installed new motor. Works like new! Problem Solved! Easy fix!

This refrigerator has the freezer on the bottom. You have to remove both of the drawers to get to the icemakeer. I did not disconnect the water line or the power to the unit because it is a hassle to pull the unit out of the hole where it resides. I first unplugged the power from the icemaker to the unit and used a flat tip screwdriver to get the icemaker out. The old one was gross. We had noticed flakes in the ice for over a year but thought it was the water. The wire bar from to stop making ice had to be moved from the old icemaker to the new one as well as a brace on the bottom of the icemaker and the front cover. This is all easy. The hardest part of the repair was getting the larger drawer back on its guide. Honestly, this was a repair my 11 yr old grandson could have done with some supervision. I'm guessing I easily saved $100 by repairing this myself.